Forum Post: Porting CC3000 to a different MCU(LPC 2148)
Hi everyone We are trying to port CC3000 to LPC2148.We have followed the steps mentioned in the attached pdf. (Please visit the site to view this file)we are able to figure out most of the code but...
View ArticleForum Post: End Device and Access Point conundrum
I'm attempting to think of a good way to implement an application cleanly in simpliciTIWhat we want isbattery powered end point periodically polled and unjoined from a mobile access pointOnce an End...
View ArticleForum Post: RE: RF1AINSTRB = 0x34 hangs the microcontroller.
Hi, I dont understand WORD read from CC430 (with )autoread. Packet has data 0xAA (first byte in FIFO), 0xBB, 0xCC, 0xDD etc... I want to read it from FIFO by word..ie integer1=0xAABB, integer2=0xCCDD...
View ArticleForum Post: MSk on 1120
The datasheet for CC1121 and CC1120 state that the receiver can do MSK, but RF studio has no option for this.Can the receiver be set up to as FSK with frequency deviation of 0.25 bit rate to get MSK...
View ArticleForum Post: The affection of Power mode on counting ticks
Hi,Development environment：IAR8.1Development Product： CC2540Using project：TimeAPPI has a function called l_McuPrecisionCount().The path is OSAL_Clock.c ->>osalTimeUpdate() finction->> tmp =...
View ArticleForum Post: RE: The reset time of CC2510
To reset the chip completely the reset pulse must be at least as long as the minimum requirement in the datasheet. There is no max number, you can hold the chip in reset for as long as you want to....
View ArticleForum Post: SCK
hey is SCK a compulsory pin which should be connected to the DEBUGGER..In my custom board i've given oly DC,DD,VDD,GND & RESET to the DEBUGGER connection..
View ArticleForum Post: RE: cc1125 spi
I had those same thoughts about both of those things. The ATMega168P chip is rated at 10 Mhz, but I believe for whatever reason, when they designed this board, they used an external oscillator that...
View ArticleForum Post: RE: CC3000 Patch Flashing Order
Hi,We are going to release a new patch programmer e/o this week which should fix a situation where a user accidentally flashed the firmware patches before driver patches.The problem on your device...
View ArticleForum Post: RE: Fake packets with own sync word
My test via cable was with these settings : // Sync word qualifier mode = 30/32 sync word bits detected// CRC autoflush = false// Channel spacing = 199.951172// Data format = Normal mode// Data rate =...
View ArticleForum Post: RE: How to send data packet when register my own CID for...
Please reply my question.
View ArticleForum Post: RE: Help eZ430-RF2500 Demo
[quote user="Tam Nguyen1"]But how to change ED, AP MAC address ?[/quote]There is a variable in the .dat file called THIS_DEVICE_ADDRESS. The value needs to be unique for every device on the network...
View ArticleForum Post: RE: Modulation for maximum bit rate that meets En 300-220-1...
80kb/s -> 40ks/s with 20kHz deviation actually does not make the grade, I missed two spurs just out of band. I had some attenuation in the cable to give a known 50Ohm impedance. If I drop the...
View ArticleForum Post: RE: TiWi-SL CC3000 Programming the service pack
Thanks Tomer for looking into this.But then you said with patch v1.10 only mac file ID and patches IDs are writable. So does it mean to write correct or default radio parameters I need to go back to...
View ArticleForum Post: Receiver sensitivity 4-GFSK vs 2-GFSK
For the C1121 what is the change in receiver sensitivity when changing from 2-GFSK to 4-GFSK ? (Assuming nothing else changes)I get a figure of around 4.8dB based on the fact that 4-GFSK has 4 levels...
View ArticleForum Post: debug session aborted
HiI am getting the following error, kindly help me to find the solution "Tue Mar 12, 2013 15:37:10: Failed to initialize communication, debug session aborted."RegardsGautam
View ArticleForum Post: RE: Using Ztool script to change Short Address of End Device
Hi, in my case z-tool works well but when I try to execute SAMPLE jscript shows several errorsError: Declaration expected.File: C:\Texas Instruments\ZStack-1.4.3-1.2.0\Tools\Z-Tool\Sample.jsLine:...
View ArticleForum Post: RE: CC2543 / CC2544 Packet Sniffer
Thanks Eirik for the reply!I have tried to sniff packets with the SmartRF Studio 7 but I got nothing. Here is my setup:-one Smart RF05EB with CC2543EM running master in PER_Test (10ms beacon)-one Smart...
View ArticleForum Post: scanning commands of CC 2540
when a scan button is pressed what command make the CC 2540 to start scanning..either a register is configured or the command is used to make this process happen..can i get those commands or register...
View ArticleForum Post: RE: Android and Bluetooth Smart - It works on the Samsung S3 phone
Hi,In our research group we officially decided to switch from iOS to Android after discussions. It is mainly because iOS CoreBluetooth API is quite high level. It is not good for research purposes...
View Article
