Forum Post: RE: How to synchronize CC1101 chips
Yes, I meant that I`m using another MCU, I`m not sure if I`m allowed to give the exact model in here, that`s why I thought that it wouldn`t work. I`m not using an EVM at all, only the transceiver. I...
View ArticleForum Post: Monopole PCB antenna - ground plane effect ?
Dear colleaguesI am not so expert for PCB antennas. So I would appreciate some advice of somebody on how to set meander monopole PCB antenna the best. My wireless network should be working in 868/915...
View ArticleForum Post: RE: TRF7970 hardware design
check that the EN line is high and the bandgap voltage is 1.6VDC, if that is good, then send a copy of your schematic and layout - must have an issue there or possibly you have a bad solder joint...
View ArticleForum Post: Can the MSP on the TrxEB be programmed with a CC Debugger?
Hi all,What options are available to program/debug the MSP on the TrxEB? The problem is that we do not have the MSP FET430 debugger. But we havethe CC debugger. Is it possible to use the CC debugger to...
View ArticleForum Post: RE: CC2520 PCB design
Hi Mohit,I sent you an email. Please send the files to me for our review.Thanks,PM
View ArticleForum Post: RE: 300 Hz Noise related to transmission timeslots using CC8531 +...
Hi Torje,I also battled noise coupling in my design. I ended up moving the antenna and RF electronics away from the DAC and analog parts. I2S on ribbon cable to the DAC. I needed some 30cm distance to...
View ArticleForum Post: RE: Internal temperature sensor in CC2540
Thanks for that highlight, John, and I'm verifying if the remainder of Section 13 applies with that differentiation. In the meantime, here is an E2E post that addresses the CAL process for the...
View ArticleForum Post: RE: C2510 IAR Idatastack error
Eirik, My settings are same as screenshot.greenja, I checked that. My code doesn't doe anything. I have written a delay routing. But I don't see the timer registers incrementing. Here's the code -...
View ArticleForum Post: RE: Can CC debug works on sleep mode?
My sleep test codevoid SleepMode(void){ unsigned int i; unsigned char Pm; EA = 0; asm("NOP"); Pm = SLEEPCMD; asm("NOP"); SLEEPCMD = (SLEEPCMD & ~0x03) | 0x02; //Enable PM2 power mode...
View ArticleForum Post: CC2530 + CC3000 SimpleLink™ Wi-Fi®
Hi,Me and my research team have been working on this new CC3000 Wi-fi module for MCU. We have successfully ported the code for the SoC CC2530 and the CC25xx familly and it works fine. During the...
View ArticleForum Post: RE: SimpleLink Wi-Fi CC3000 with CC2530
Hi,Ok, done.Thank you for your reply.Best Regards,Tiago Gomes
View ArticleForum Post: RE: Slave standby - how to control power on, reset and amplifier...
Hi Thomas, Status LED is not the best option here. For any audio device you have the option to control up to 4 GIO pins as the CC85xx goes through the different states. Please have a look at the...
View ArticleForum Post: RE: Configuration for PCM5310 at PurePath Config tool for CC8530
Hi Flavio, This can be added by yourself. Please read and understand the 'Audio Device Definition Files' segment in the Configurator Help menu. The CC85XX User Guide will come handy when doing this and...
View ArticleForum Post: RE: The affair in which connection is cut using CC85XXDK-HEADSET
Hi Hirokuni-san, You can look at our PurePath Commander tool:http://www.ti.com/tool/purepath-wl-cmdThis is a PC tool that allow you to do basic RF testing. If saturation occurs it should show up when...
View ArticleForum Post: RE: do sensortags work with non TI usb dongle?
you can use that. As long as you load the correct hex image onto the flash.
View ArticleForum Post: RE: Problems connecting to SPP Server from Windows
Hi Clive,We are working on this and will get back to you.
View ArticleForum Post: RE: TI-MAC 1.1.0 Source code
hi,we need TI MAC to debug our CC2530 system for our wireless lock project，thanks
View ArticleClik here to view.
Forum Post: RE: CC2540 USB Question
Hi Greenja, I would like to know why there is P1_0 pin connect to USB D+R32 and R92 are the pulled-up resistor for the D+, why we need to add the P1_0??Thanks
View ArticleForum Post: RE: SmartRF05 Development: What IDE, where is the demo source?
Yes, the 30-day 'KickStart" evaluation version is a Full version of IAR that is required to compile the Large BLE projects. Any version of IAR above 7.51 are recommended for use with BLE. With the...
View ArticleForum Post: RE: Reading samples from ADS1292 - cc2541 interfacing with...
What are your clock settings on CC2541 and ADS1292r? Have you choosed fCLK=512KHz divided from the clock of cc2540 and SCLK=1MHz ,just the same as the MSP430 demo? I used a 2.048MHz oscillator as fCLK...
View Article