Forum Post: RE: CC2510 register config using SmartRF studio
I don't understand the Random field still.I am using smartRF studio to configure RF registers and not doing any RF testing.The payload will be specific data(like number of button presses or...
View ArticleForum Post: RE: CC2540 USB Dongle as a slave
I have opened BTool and performed the above instructions which should make the dongle act like a slave. However, when I have completed this how do I get the dongle to start advertising?I look at other...
View ArticleForum Post: RE: wlan_connect return 0, but no callback, how to debug?
Hi Yael,perhaps an question in same area:What is the correct behaviour after wlan_connect is executed and e.g. key is wrong, SSID is wrong, AP is not more available.Do i get an event? How long shall i...
View ArticleForum Post: CC2540 to get iphone bluetooth address
Hi：Environment is CC2540，iphone5 and BLE stack V1.3。In SimpleBLEPeripheral project，after connect with iphone5, I try to use GAPRole_GetParameter( GAPROLE_CONN_BD_ADDR, center_addr ) to get the...
View ArticleForum Post: RE: Changing I/O pull from low to high
Thank you Chatto,I'm on vacation now so will check that out next week.Thanks
View ArticleForum Post: RE: How Unicast?
When ZED joins ZC, there is end node announcement that includes the shout address of ZED and you can use that to do unicast. The example of unicast would be like the followings: afAddrType_t...
View ArticleForum Post: RE: Bluetooth application development with Link layer modification
The reason for the lack of devices for BT v3 was that there where too many requirements that made it unattractive to developers. Most developers and manufactures skipped v3 and went to v4.0. It has...
View ArticleForum Post: RE: CC2533 for Android Driver
I think CC2533 is for RF4CE not Zigbee ZStack, isn't it? Anyway, the communication between host and CC2533 is either SPI or UART and the Linux driver should be inside your Linux BSP.
View ArticleForum Post: RE: Auto Channel Selection in Wl1271
Hi Abhijit, As of now we are setting the AP channel manually and connecting the stations, in this situation we are not sure if the selected channel is the right channel ( which has less...
View ArticleForum Post: RE: Strange CC2530 flash write issue?
I do think data in NV flash would be changed whenever power is unplugged and plugged. I would suggest you to check the return value of osal_nv_write(LIGHT_STATE, 0, 1, &lightState). Check if it...
View ArticleForum Post: RE: auto start zigbee coordinator
If you do not enable NV_RESTORE in your projects, it is normal that the short address would change. In general project, you need to enable NV_RESTORE so you can keep the network status after power...
View ArticleForum Post: RE: Coordinator software reset - network not functioning
It is weird that you can not debug using USB power only. I suggest you to review your schematic about USB power. You can refer to the CC2531 schematic from swrr067.
View ArticleForum Post: RE: CC1125 = CC1120 = CC1200 at certain config?
As far as I know the transparent mode datapath is equal on the 3 chips and hence the result should be same for the same settings.
View ArticleForum Post: RE: CC1120 CCA (Clear Channel Assessment)
I believe there are some threads out there that should answer your...
View ArticleForum Post: RE: CC3000 SPI Clock Polarity and Phase
The documention adjustment is unclear and grammatically incorrect. Grammatically, you have two sentences joined by a comma with no conjunction. For clarity, you should specify the value of CPOL. You...
View ArticleForum Post: RE: changing Generic Audio DAC data out pin to AD1
I mistyped. It is AD1 by default, I'd like it to be AD0
View ArticleForum Post: RE: Unxpected Result for HCI_CMND_READ_SP_VERSION
I have determined the cause of the issue. The MCU is a 5V device, whereas the CC3000 is a 3.3V device. I was using transistors to level shift as per an EE's suggestion. Another EE suggested I try...
View ArticleForum Post: CC2520 burst reads at max SPI speed unreliable?
I've got a CC2520-EM (v2.1) connected to a TrxEB (MSP430F5438A). The CC2520 is configured to interrupt on RX_FRM_DONE, at which point the MSP430 application wakes and reads the packet into memory. In...
View ArticleForum Post: RE: wireless video transmission
Hello Bhargavraj,CC3000 is not really made for HD video transmission. I'll go ahead and move your thread to discuss some of our other Wifi products Regards,Aaron
View ArticleForum Post: RE: Connection via "First Time Config Probe and Beacon...
Hi Thomas,Could you please try patch programmer 1.10.1 instead, and follow these instructions? :http://processors.wiki.ti.com/index.php/CC3000_First_Time_Getting_Started_Guide Regards,Aaron
View Article