Forum Post: Bluetooth stack load on MSP430BT5190 + CC2560
Hi, In one of our design, we are considering to replace MSP430F5529 with MSP430BT5190 to enable bluetooth connectivity.Ā So the question is whether 5190 has enough MIPS available in to run our control...
View ArticleForum Post: CC4305137: Multiple End Devices communicating with an AP, getting...
I'm working with the CC4305137 and trying to get multiple End Devices to communicated sensor data to a Access point. Ā The AP will use the data internally. Ā I'm working in the 315mhz range. Ā I can get...
View ArticleForum Post: TRF7962A Clock Speed
Hello All,Because a function of MCU to use is limited, I want to control TRF7962A with DATA_CLK of 200kHz.(Serial Interface Mode)Is it possible?In the case of such a low clock speedĀ , does anything...
View ArticleForum Post: RE: CC2540 HCI over UART0 using CC2540EB build.
Hi Tyrell,Ā Ā I am using CC2540EB configuration for HostTestRelease. HCI over USB is working well with Btool, but it failed for HCI over UART. Is there any tricks?ThanksJack Lam
View ArticleForum Post: c code to send at cmmand and receive ok
hiii am using TMS320C5515 AND TELIT GL865 AND TXS 0102 as voltage converterand code composer studio v5i want to send AT command and receive OK but am not getting ok ,i don't know what is problem and...
View ArticleForum Post: WPS in WL1271
Customer question:Ā Does WL1271 support Wifi ProtectedĀ Setup (WPS) then?Ā I see that WL8 does.Ā For WL1271, the data manual indicates<<Supports requirements for Wireless Fidelity (Wi-Fi)...
View ArticleForum Post: Wifi wakup vs Zigbee
Customer question:Ā How fast is Wifi wakeup time (in WL8) versus Zigbee? Could not find WLAN wakeup info in the WL8 datasheet.Ā Thanks,Shalini
View ArticleForum Post: Windows 8 compatibility
I cannot get my Windows 8 PC to work with SmartRF Studio, does anyone know if Windows 8 is supported.Ā
View ArticleForum Post: RE: Range optimization
Maybe this is also of importance that the CC85xx slave module (your hardware) is placed very close (<10 cm) to a digital amp and PWM-driven FET-basedĀ powerĀ volume control. The output PWM power...
View ArticleForum Post: Inquiry! host-control of 2 mic and 1 rx
Dear Sir.Ā Ā Two TXĀ used the CC8520dk & ADC3101,Ā one Ā RXĀ usedĀ CC8520DK & DAC32.Ourprogressthedatacommunicationsuccess, however,the openingsounddoes not.Ā Please refertoCC debuger settingĀ value...
View ArticleForum Post: RE: How to implement group Addressing by using Monitor and Test API.
hi, do you had success? i send it ok, use the API 'AF_DATA_REQUEST_EXT',the data is :0x1a, 0x24, 0x2, 0x1, 0x1, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0xd, 0x0, 0x0, 0xf, 0x5, 0x0, 0x0, 0x20, 0x1e, 0x6,...
View ArticleForum Post: RE: Invalid short address (0xFFFE) on an end device
I also have the same problem.
View ArticleForum Post: RE: why is only the group id 0x0001 is worked?
when the ED send frame which the dst group id is 0x0002, the coordinator can receive it, but not will transmit to AF layer, only send back to as one broadcast(by packet sniffer, I can see the path).
View ArticleForum Post: RE: Re:USB detection error
Please check the items I listed in my last post.Fredrik
View ArticleForum Post: RE: power supply solution for low power rf
IĀ asume you are looking for a DC/DC with bypass mode since you want a similar device to TPS62730. To the best of my knowledge there are no alternatives with 3.0 V output voltage (TPS62730 does not have...
View ArticleForum Post: RE: CC2543: FSC_look on pin using RFC_OBS_CTRL
No, this does not affect the reliability. The PLL will be in lock, but the lock detector will not report it. The reason is that for the lock detector to report lock, the PLL has to have been in lock...
View ArticleForum Post: RE: CC4305137: Multiple End Devices communicating with an AP,...
Sounds to me like one of your sensors is hogging the available bandwidth. 100 mS between broadcasts may be too short, depending on your baud rate and packet length. What is you baud rate? It looks like...
View ArticleForum Post: RE: CC2541 BLE - will not enter "Sleep" Mode
Hi!I'm from Catalonia :)Sure you can make it to not be auto-discoverable! Check the code, and comments!Perhaps if you search for "auto" you will find it :) Yes, I now remember and there was a clear...
View ArticleForum Post: RE: CC Debugger can't see CC2540
Zodryn,DO you have the R1 resistor? if it is connected, use the pin 9 to supply the board.Also, along with Igor's suggestions, you have to ensure that the crystal is connected properly too.
View Article