Forum Post: RE: AF_DATA_REQUEST_EXT using 64bit addressing when network size...
Hi Derek,For your reference, I had increased the number upto 80 and do not experience running out of RAM.
View ArticleForum Post: RE: CC2530+CC2591EM and Z-Stack 2.5.0, compilation flags
Hi,I have been performing a packet txrx test using our device (tx) and a eval board (rx). When I use smartrf studio tx'ing through our device I get about about 5dbm higher rssi on the receiver than...
View ArticleForum Post: RE: Is there Z-stack support for external NV memory for OTA on...
Hi,It seems that there is less supportive on MSP430 ZStack from TI. I would like to suggest you to apply ZStack on CC2530 directly. We have no problem using different external flash to do OTA on CC2530.
View ArticleForum Post: RE: ZigBee Green Power
Hello,TI is a ZigBee advocate and promoter and closely following every profile spec evolution and adoption.I am sorry but we can't disclose roadmap information on a public forum. I recommend you...
View ArticleForum Post: BLE Advertising packet encryption
Is it possible to encrypt an advertising (broadcast) packet in BLE using the AES?
View ArticleForum Post: CC2540 Op Amp to ADC pin connection
Dear TI/E2E,Is there a need to physically connect Op Amp output pin P0_2 to another pin as an ADC input? Can P0_2 act as both the Op Amp output and an ADC input? Haven't gotten around to test it, but...
View ArticleForum Post: How do I find CC2531 Nano USB sticks
I see a wiki that describes a product that is supposedly ready for production and already FCC certified called the CC2531 Nano USB. Other than in the CC2533 dev kit, I can't find how to order the...
View ArticleClik here to view.
Forum Post: How to Switch on LED in CC2540 Keyfob attached to P0.6 and P0.7
Hi everybody,I am working with the cc2540 mini Dev-Kit.I want to turn ON LED connected to P0.6 for few seconds.I'm usingsimpleBLEPeripheral example. Setup as on the picture below.P0.7 is set to LOW...
View ArticleForum Post: RE: LF RFID Reader
Thank you, that makes it very clear for me. The only other question I would have is can it read multiple tags at once?
View ArticleForum Post: RE: Is CC Debugger needed in autonomous mode？
Thank you very much!So if i want to use CC85xx devices for development,i must need a CC Debugger or GangPro-CC,right?The PurePath Wireless Commander is used for the production,but it's help mentions...
View ArticleForum Post: RE: MT +Z-Tool support for Home Automation
Yes, there is no problem using MT interface to make HA profile support using CC2530 with ZStack. We have done it in our products.
View ArticleForum Post: RE: CC85xx simultaneous transmit and local playback
I'm not sure where to access 'PurePath Wireless Configurator help system'.. is there something online/pdf, or are you referring to installing the program and accessing the help menu within that??After...
View ArticleForum Post: RE: CC85xx slaves
Yes, true, with the CC85xx, but we could use a generic LPRF device. Here is an App Note for using the CC1101 at 900MHz, which could also be an advantage for longer range:...
View ArticleForum Post: RE: CC2540 connection problem
Hi Chatto, Problemed solved! It turns out that I didnt solder the Balun well so that there are so interference with the RF. The custom boards I got back from the SMT factory worked well!! Thanks for...
View ArticleForum Post: RE: Is there Z-stack support for external NV memory for OTA on...
Your suspiciousness might be right. There might be not more support for CC2530. However, we have the experience to use different external flash to do OTA on CC2530 with ZStack by ourselves and that is...
View ArticleForum Post: RE: Open Source Compiler for CC2540
All, Interesting reading, I have one additional comment to the original question. We have a "network processor" version of our BLE chip called the CC2541S, here the BLE stack is preloaded onto a device...
View ArticleForum Post: RE: CC2510 newbie
David, Please refer to section 6.2.1 on page 8 for the minimum requirements for getting debugging to work on our CC25x series devices. From what you write, you are missing the RESET pin. Please...
View ArticleForum Post: RE: CC430 audio loopback
Tim,I posted an earlier E2E post where I implemented a similar demo as you are doing but using a different MSP430 and a CC1120. I believe you should be able to look at my code (posted on E2E) to see...
View ArticleForum Post: RE: About PurePath Wireless(CC85xx)
Completely agree testing is required too.. but it would be a waste of time if you were expecting way off, so more numbers please, just add the disclaimers!Are you saying that there is no benefit to...
View Article