Forum Post: RE: First time config and wlan_add_profile
Hi Edward,Thanks for moving your post to a new thread :).1) Have you updated the firmware with the latest version of the patch programmer (v1.10.1)? I would recommend updating with the latest version...
View ArticleForum Post: IRQ Line never goes low after initial command
Greetings. I am using a TiWi-SL REV2, and have everything hooked up to the logic analyzer. I have verified that my initial sequence of PWR_EN high, wait for IRQ to go high, wait for IRQ to go low, Drop...
View ArticleForum Post: RE: WiLink 8 could not get configuration binary ti-connectivity...
hi,Make sure if udevd is running. Ans also cross check for proper udev rules.I would suggest cross verify with sdk filesystem and see if you have proper rules similar to /etc/init.d/*and /etc/udev.try...
View ArticleForum Post: RE: CC2530 A2530E24A-LPZ Temp Sensor Code
Hi gurudas,You can find the link to the CD of the A2530E24A-LPZ over here : http://www.anaren.com/sites/default/files/uploads/File/A2530-ZigBee-BoosterPack-CD.zipYou will find all the Souce code on the...
View ArticleForum Post: RE: MSP430BT5190 + PAN1323 Slow Clock
Hi Edwin,The slow clock is required for proper operation of the device at all times: http://processors.wiki.ti.com/index.php/CC256x_Testing_Guide#Device_Power_UpThe slow clock can be driven by any...
View ArticleForum Post: RE: CC1101 and RSSI reading
Hi StefanoThank you very much for the info. I tested in a soccer field and can only get about 50m about 1.5 meter above ground. By the way, are you able topinpoint me to the doc or gerber for the ev...
View ArticleForum Post: RE: spectrum analysis using cc2541
hello Fredrik,Thanks for your response. I want to detect WLAN signal as well, analyse the spectrum and send the output data via BLE . So can I use the same device cc2541 for all of this or do I need...
View ArticleForum Post: RE: Timer1 Channel 2/3 can't give PWM
Hello Rui,Did you manage to get your code to produce a PWM output on P0.4 (ch2) and P0.5(ch3) the same way the code in the posting does? If not take a look at both the Keyfob and USB Dongle Schematic....
View ArticleForum Post: RE: cc3000 patch programmer 1.10 problem
Hi Victor Nixto,I am using LSR TIWI SL module with non TI micr. So could you please the code that you have to implemented. This will help for implementation.one quick what is the need to set for...
View ArticleForum Post: RE: Does signal attenuation depend on channel, specifically for...
Thanks for your reply. According to my measurement, there can be a few dB's difference for the same link using different channels such as 19 and 26.I have two additional questions:1) Does signal...
View ArticleForum Post: RE: CC2540 ADC sampling while transmitting
Reading the ADC from an event does not provide accurate timing. I need to sample the signal at exact intervals with as little delay and jitter as possible.The OS times tasks only in an approximate...
View ArticleForum Post: RE: CC2530 A2530E24A-LPZ Temp Sensor Code
Dear MDani,Thanks for the CD.Can you just tell me from those examples provided there on CD which files are to be burnt on MSP430 for Demo Application.Wherein the temp sensor senses the temp from End...
View ArticleForum Post: Blue radios BR-LE4.0-S3A or Panasoic PAN1721
Hi,Quite new to BLE and modules and development, but I am trying to research so I can take the info to a development company to get them to create a small device with a sensor.However I am torn between...
View ArticleForum Post: RE: Initial Bootloading through USB cc2540
Hello John,Where exactly does it say you can bootload a blank CC2540 through UART? I was under the impression that you needed a CCDebugger or your own flash programmer in order to program the chip....
View ArticleForum Post: Can I use SMS notification service in iphone without jailbreak???
there are many smart watch that support Caller-ID notification, SMS notification.Q1. which profile is used when I use 'SMS notification service' in iPhone without jailbreak??I heard that third-party...
View ArticleForum Post: Programming problem
Hi,First ,sorry for my bad English.When I try to program the CC8520, the PPWC shows Flash Erase Failed . I check the ppw_programmer.log file,it shows:Reset(doSpiReset=0, enterSpiLoader=1) ->...
View ArticleForum Post: RE: CC8520 Flash erase failed
Hi ,I got the same problem, How to choose the crystal and capacity ? I use 48M and 33pf which used in the HeadSet demo, but it still failed .
View ArticleForum Post: Transferring data between Peripheral and Central Device
Hello everybody,I'm quite new in BLE devices.I bought a CC2541DK kit and I started playing with SimplePeripheral and Central examples. I managed in understanding advertising, scanning and connection...
View ArticleForum Post: RE: CC1111 AP freezes after CC1110 ED loses connection
I was hoping that some TI employees would be watching over this forum and was really looking forward towards receiving some help from experienced engineers. Did I provide a too loose description of the...
View Article