Forum Post: RE: Modifications of CC1125EM-CAT1-868 board for 902 – 928 MHz band
Hi Rob,Yes, correct, section 9.3. Thanks for pointing that out.
View ArticleForum Post: RE: CC112x: dependies of CH.BW, Symbol rate and Deviation
Could you please be more specific what you are looking for? As a general rule the signal is easier to demodulate the larger the deviation is but the larger the deviation gets the noise in the channel...
View ArticleForum Post: RE: CC2530 & CC2531 Silicon Revision History
FIPS certification. We are certifying against a certain rev of the silicon and need to know that rev and include that requirement in config management plan.
View ArticleForum Post: RE: RI-STU- MRDx BCC
Found the error.I used an external comport-library (Delphi XE) and there was an unicode-error resulting in wrong translation of unicode... Fixed it, now everything works fine (phew!)Thanks everybody...
View ArticleForum Post: RE: WiFi calibration on wl1271
Hi Gina,Hi All,We have custom platform based on OMAP4460.The WiFi module used is wl1271 jorjin. We have used TQS_S_2.6.ini file to calibrate it.But during calibration we are getting error.root@Vega0:~#...
View ArticleForum Post: RE: communication problem between cc430 & cc1101
Hi Bijendra.I am also trying to communicate between CC430F6137 and CC1101. But I am not getting any data in cc1101.CC1101 is used as receiver. Can you suggest me some idea.Thanks and RegardVivek Kumar
View ArticleForum Post: RE: RF SOC based EVM from TI
You'll need to write a new board-support-header for this new board, but that isn't too hard. Otherwise, this is the best dev kit for OpenTag on CC430, it is just a bit new so the board-support-header...
View ArticleForum Post: CC3000 PS-Poll
Hi,Does the CC3000 support PS-Poll power saving? If the answer is no, then is that on the roadmap?Thank you,
View ArticleForum Post: RE: IRQ Line never goes low after initial command
As for the other questions, the MCU is a an energy micro, and the SPI lines are connected as follows:MOSI (labeled SPI_DI in logic analyzer capture): Direction: MCU->TiWi. Connected to TiWi-SL EM...
View ArticleForum Post: RE: Getting started with CCS and CC3000
Hi Kelvin,I have read a lot before posting and your reply was one of the few that made sense, so I decided to post a basic issue here.I have installed the Patch Programmer...
View ArticleForum Post: RE: CC1101 as a RX with smartRF
Oscar,Hello, what did you find was your problem?I have having the exact same issue...apparent data on the GDO1 pin with NO RF input signal.I have tried the FIFO settings and only make small...
View ArticleForum Post: RE: Which free C compiler for 8051 is the best ? or IAR EW8051 is...
To develop TI Zigbee application on CC2530, IAR EW8051 is the only choice.
View ArticleForum Post: RE: Problem with SmartRF TrxEB
Hello.Thank you for your help. But we still get a little confused about it and we have no idea about how to program the original code to the chip (also no idea how to reprogram the MSP 430) We have no...
View ArticleForum Post: RE: Compatibility between XBee smart plug and Smart RF05 board
From datasheet of Xbee Smart plug, it uses zigbee mesh network but not metion which profile it uses. If you can make sure which profile it uses, you could program Smartrf05 with cc2530em to received...
View ArticleForum Post: RE: UBL details
Ralf,If you look at ubl_main.c, specifically the __low_level_init() function, you will see that VERY early in the reboot process, the code tests to see if the reboot was caused by a watchdog timeout....
View ArticleForum Post: RE: Bricked Keyfob
The SmarRF does the reset. On the SmartRF, can you read the IEEE number?You can also change the speed from fast to slow that may work. Can you send a screen shot of the SmartRF?
View ArticleForum Post: RE: communication problem between cc430 & cc1101
Hi Bijendra.When I used two CC1101 module then there is good communication between both module. But when I used one CC1101 as receiver and one CC430F6137 (EZ430-Chronos developement board) as...
View ArticleForum Post: RE: CC2538 availability
HiSampling parts now but what about the dev boards? I guess specifically the CC2538EM board since the SmartRF06 system appears to be in stock.I saw mention in a presentation of a larger kit containing...
View ArticleForum Post: Problem In communication Between CC1101 and CC430F6137...
Hi When I used two CC1101 module then there is good communication between both module. But when I used one CC1101 as receiver and one CC430F6137 (EZ430-Chronos developement board) as transmitter, I am...
View ArticleForum Post: RE: RF SOC based EVM from TI
Hi JP NorairThank you very much for your reply,We had some query regarding board selection which is mentioned below.============================================================================...
View Article