Forum Post: RE: HTTP Server Application Code
Geet Modiit has been a month the link is still not active(but they have explained all the codes in the above given wiki link.think webmaster forgot to link the download file.
View ArticleForum Post: RE: How to get the extended pan ID at the application layer, when...
Extended PAN ID is used for joining a specific zigbee network and is specified by manufacture. If you don't have Extended PAN ID specified on your zigbee device, it will choose any one proper to join....
View ArticleForum Post: RE: cc1101 in freq 403Mhz
See http://e2e.ti.com/support/low_power_rf/f/155/t/218354.aspx
View ArticleForum Post: RE: CC2520 status byte: meaning of exception channels swapped
Hello Ubisys-ah,Are you sure this is really a problem and not documented in errata sheet.?I am working on the CC2520 for the Automotive Application. Your help is highly appreciated.Best RegardsChandu
View ArticleForum Post: What BLE services should my custom peripheral support?
We are planning to create some new BLE peripheral devices that expose sensor measurements via BLE. Where it makes sense, we wish to implement services already defined by bluetooth.org to expose our...
View ArticleForum Post: RE: Internal temperature sensor in CC2540
Chatto,The CC2540 datasheet saysVoltage coefficient: 1 / 0.1 V is misleading.Now, the temperature coefficient = 2.7259 mV/1°C that solves my question. Best Regards,CK Lui
View ArticleForum Post: How do I assign uuids for the custom primary service that my...
I am implementing a custom BLE peripheral that exposes some unusual sensor data, so I have decided to have my device implement a proprietary service. How do I assign a uuid to this service that is...
View ArticleForum Post: Integrating TiWi-R2 (WL1271) with AM3354 using 1.8V SDIO/MMC?
Hello,We have designed and made a prototype board using the TiWi-R2 module (encorporating the WL1271 chip) wired to MMC1 on an AM3354, and the power feeds for the corresponding port wired to 1.8V...
View ArticleForum Post: RE: loading the service pack for the CC2560A
Hi Zahid,We are also having trouble interpreting the commands/return codes that are shown in the “CC256x Testing Guide”. Is there a document with what does each byte means in the response?Thanks for...
View ArticleForum Post: RE: OSAL Design/Architecture
Hello TI Employees and other Devs,I am part of a team using the CC2541 EM R1.1 and CC2541 Mini Development Kit. We are trying to figure out the OSAL before we can tackle the BLE stack. So far our...
View ArticleForum Post: Can't find COM7/COM8 port on HP Laptop (CC2541 mini development kit)
Dear Sirs,I've installed BTool - BLE PC APP - v1.40a at HP Laptop (Pavilion dm4-1 1 60us. The follow instruction to identify the COM Port Number shows:Other devices:----? CC Debuger----? Unknown device...
View ArticleForum Post: RE: Timekeeping on CC2540
What is your clock source? Is it systematic drift, or temperature-induced drift? You could calibrate each clock with your external reference based on a temperature table and adjust accordingly.
View ArticleForum Post: Jorjin WG7310 / WL1271 - WinCE 6R3 - BT stops transmitting after...
Hi,We are using a Jorjin WG7310 (WL1271) radio module in a system running WinCE 6R3. We are experinecing a problem wherein the BT radio shuts itself off after10 minutes of operation during FCC...
View ArticleForum Post: RE: Question with CC2541 working with TPS62730.
hello Chatto, Another question related to the voltage shift is the cc2541's pins' voltage is 0-3v when the supply voltage VDD=3V, so when the vdd changes to 2.1V , will the outputs of CC2541 change...
View ArticleForum Post: RE: CC2564 Pinout and Connection Inconsistencies
Hello,The correct configuration is:A10, A11, B9, B10 -> GNDA14 -> NCSorry for the confusion, please refer to: http://processors.wiki.ti.com/index.php/CC256x_Schematic_and_Layout_Checklist
View ArticleForum Post: Too many exceptions raised .. How to avoid
Hello,We are using the CC2520 RF chip for the automotive application. but we have a problem that we have too many exceptions raised.Is there any way how we can avoid these exceptions.? We have the...
View ArticleForum Post: RE: The Server does not receive any data
Hi,Check your Patch Version and your Firmware Version First.Best Regards,
View ArticleForum Post: RE: Set Osal Events
I just have a look at your attachment and your codes are just too erratic. I have no idea about your intention. Could you describe why you want to do that? Maybe we can find out another approach to do...
View ArticleForum Post: RE: CC2530 RF Test Signal
You can use the following commands to turn the radio on and off:#define SRXON do{RFST = 0xE3;}while(0)#define STXON do{RFST = 0xE9;}while(0)#define SRFOFF do{RFST = 0xEF;}while(0)/Fredrik
View ArticleForum Post: RE: CC2530 range
If you want to go through the floor directly, even it is only 1 meter, you should increase the TX power not decrease it. However, it still depends on the material of your floor.
View Article