Forum Post: RE: Problem connecting the dongle to a PC
Hi guys,I am also working on a project and I am using CC1111 dongle. I uploaded the program through the debugger form IAR workbench and the nodes communicate fine. But when i plug the usb dongle into...
View ArticleForum Post: RE: CC254x chips life cycle
We received feedaback that the life cycle of the CC254x family is as good as it gets in terms of ICs and furthermore there are 2 seperate fabs making supply more secure
View ArticleForum Post: RE: USB not working with PC
Hi Joe,Did you solve your problem by any chance because I am having the same problem? Please do let me know I you found the solutionThanks!Sean
View ArticleForum Post: NFC and BT Smart - (CC2541+ RF430CL330H) - Pairing BT Smart via NFC
Hello E2E,Are anybody working on using the CC2541 BT Smart for direct or indirect pairing? with RF430CL330HHere are a few example with Classic BT:Using TI Technology to Simplify Bluetooth Pairing Via...
View ArticleForum Post: RFID Receiver for read data from TPIC80000(TPMS EVM)
Hi AllI 'm researching about Tires pressure monitor system , I found the TI solution for this, but I have a question :" Is there any module of TI for read the transmit data from TPIC82000 or solution...
View ArticleForum Post: RE: CC113L and CC115L recieve problem
HiIt can either be register settings (please start by testing with one of the typical settings from SmartRF Studio and the change the registers when you have a stable link) or it can be your HW.It is...
View ArticleForum Post: RE: End-device binding with one device the Coordinator
Hi azeddine,I have make some mistake in my reply. Since you use ZDP_BindReq, the message callback should be in the case "Bind_req/Unbind_req" of ZDApp_ProcessMsgCBs, which is located in ZDapp.c. You...
View ArticleForum Post: RE: C1110 Power mode 2 Wakeup
Hi EduardoThe CLKCON register is not related to the SLEEP timer in any way. If you look in the Sleep Timer Section of the data sheet you will see the following:“Note: In this section of the document,...
View ArticleForum Post: RE: CC2530 transmission distance and POWER_SAVING
From ZStack, I do not see this difference. I would suggest you to use spectrometer to measure TX in dbm.
View ArticleForum Post: CC2540 DK-MINI discovery behaviour
First steps with the Keyfob - discovery won't work ...(paragraph references are to swru270c.pdf)4.2 …“At this time you will want to insert the battery (or remove and re-insert the battery to reset the...
View ArticleForum Post: RE: WL1271L Unique id
Ya i already tried barakWhen i changed that nvs file id into 00:00:00:00:00:00 via calibrator command.it could be changed to that 00:00:00:00:00:00 from the previous one.when i reboot again to see the...
View ArticleForum Post: RE: HCI_Read/Write_Stored_Link_Key, Initialization of Dual-mode...
Thank you both, helped very much.So is it really true that the BR/EDR/CB module will be "switched off" if I don't call any functions that rely on it? What does that in practice mean, of course I'm not...
View ArticleForum Post: RE: Module maker and antenna design
Hello,Any of our 3rd party RF design houses could offer this. We have worked with LS Research on RFID/NFC designs several times, so this may be a good place to start. We do not have anyone designing...
View ArticleForum Post: RE: CC2541 radiated emissions failures at
The FCC/ETSI testing code example was meant to be a sequential '10 push' sequence for the keyfob for different radio states and frequencies. It was not meant to demonstrate hopping.
View ArticleForum Post: CC2543 & Srf05
Hi,I used IAR to program the CC2543 mounted on srf05 board and achieved the data transmission. I was using SmartRF 7 software to infinitely send packets, while on the other side, the programmed board...
View ArticleForum Post: RE: cc3000 as access point?
Hi ZahidThanks for the answer. With a CC265x, I will be able to transmit 100m, but I presume receive range will be limited by the mobile phones cf. 10m?
View ArticleForum Post: RE: Bluetopia stack: The data cuts when transmit it continously
Hi Stonestreet One,I am interestedin sharingmycode.Hope your answer.RegardsCarlos
View ArticleForum Post: RE: PeerToPeer connection between TRF7970A evm and Android...
Victor - pls. use attached to demostrate P2P using the EVM with the NFC enabled handsets or between two EVMsDocklight can be downloaded from here ==> http://www.docklight.de/download_en.htm (Please...
View ArticleForum Post: RE: Changing Transmission power level in Bluetopia stack
Hi,For BLE, the output power is set to 10dBm. For BT, the output power changes between the power levels during regular operation using power control See Vol 2, Part A Ch.3 of the BT specs:...
View Article