Forum Post: RE: CC1101 Unknown Mode
Hi I'm using the CC1101EM 2.1 868/915MHz module from TI and I have the SmartRF04EB 1.9 evaluation board. When I send the STX and SIDLE from SmartRF everything works fine. I use SmartRF and the...
View ArticleForum Post: RE: receiving sms and email notification in bluetooth headset
Hi Anirban, Can you post some more details about your configuration? The hardware that you are using, the Bluetooth profile that you are using to connect to iPhone etc. Best Regards, Stonestreet One.
View ArticleForum Post: RE: Bluetopia, SPP Mode Continuous Data Sending
Hello Naofumi, What is the baud rate that you are using the device at? Can you also let us know the revision of the MSP430 chip that you are using? It should be on the top of the chip. We know about...
View ArticleForum Post: RE: Trouble with AGC_CS_THR for a CC1120
Actually the problem is that I loose the Carrier Sense before I loose my packets. I output the CARRIER_SENSE and the PKT_SYNC_RXTX on GPIOs and when I do a test range, I see an activity on the CS up...
View ArticleForum Post: Tethering and hotspot for wl1271 omap3 processor
Hi All, I am working on omap3 processor android system. wifi chip is wl1271 model. Linux kernel using is 2.6.37 i am working on community version of android gingerbread, wifi is working fine. where as...
View ArticleForum Post: RE: How to send actual data between two CC1101
Modulation formats. 2FSK, 4FSK, 2GFSK, OOK/ASK Frequency ranhe 300-348 MHz; 291-464 MHz; 782-928 MHz All this information is on CC1101 web site (http://www.ti.com/product/cc1101) and in the CC1101...
View ArticleForum Post: SimplicTI
I have the SMARTRF05+CC2533/2543EM. I am trying to load the CC2530 sample application to the cc2533-DK(SMARTRF05+CC2533EM). I was able to load with IAR EW8051 and clean and rebuild with no error....
View ArticleForum Post: RE: Enable BT on DM37xx platform...
Hi Naveen, I am using android gingerbread and kernel version 2.6.37 I have seen BT_EN pin pulled high while turn on. Only change on my board agenet OAMP3EVM is uart port number and BT_EN gpio pin....
View ArticleForum Post: RE: CC3000 Patch Programmer problems
Hi, i'm glad that you found the issue. In the murata data sheet schemtaic I see short between FUNC2 and WL_RS232_TX ( no 2Kohm). can you please specify which reference design did you use? since it...
View ArticleForum Post: RE: Wl12xx calibration Issue with DMA
Hi, We have tried your sequence on one of our platforms using the latest R5-SP3 drivers and had no issues. It might have been an issue with an older driver/firmware version. Are you using the nlcp...
View ArticleForum Post: RE: ANT Continuous-Scanning channel - Collisions?
Hi Ragnar, I would recommend looking up the ANT Basics video describing ANT's built-in Isochronous Ad-hoc Time-Adaptive Multiplexing scheme which you can find at the thisisant.com website under...
View ArticleForum Post: RE: How to let zigbee FFD works as coordinator or router...
Hi, I think the ZNP is a good example to learn how to handle with the device's type. regards, Ilya
View ArticleForum Post: RE: EZ430-256x Sample Apps "EZ430-ACCL" question.
Im using the ez430-rf256x, which comes with the mindtree stack for use with IAR. Are you saying there is now a different bluetooth stack i can (or am supposed to) use?
View ArticleForum Post: Maximum Number of Sockets
If I call sockets() repeatedly 8 times, it will return handles from 0-7. On the 9th call it returns -128 (an error). This seems to indicate that I can create 8 sockets. If only 4 could be created...
View ArticleForum Post: Delayed Transmission with High Slave Latency
Hello, I am working with CC256x/MSP430 peripheral in slave mode using the Bluetopia's BLE stack. I am connected to the device with the settings ~20 ms conn interval, >100 slave latency. I've...
View ArticleForum Post: RE: CC3000: Socket() API able to create 8 sockets
Hi Andy, Please look at the post in this thread. Regards, Abhijit
View ArticleForum Post: RE: Packet descriptors in the wl127x
Hi Brend, there are 4 queues one for each AC (access category like Best effort, Voice, Video... according to WMM standard) and the firmware will transmit them one after the other (from the high...
View ArticleForum Post: RE: Is CC2540 digital output open collector?
Yes. So, just to be sure the output stage is like an inverter.
View ArticleForum Post: RE: CC2540DK and Motorola
Android really does hate the idea of BLE functioning properly doesn't it? Had a little look around the Motorola forums, it appears that ICS broke their BLE API and they said they are planning/working...
View ArticleForum Post: RE: ANT Continuous-Scanning channel - Collisions?
Hi, just to provide some additional clarifications. As a note, ANT master channels do typically take a brief receive window to find an open timeslot before broadcasting, so they do have some measure of...
View Article