Forum Post: RE: How can the "CC2540 USB Dongle" sniff a conversation between...
Hello Hector,Welcome to the Forum!I have notice a similar thing using Windows XP. You have to stop and start the Sniffer several times or start and stop the advertisements and then the connection will...
View ArticleForum Post: RE: New BLE-Stack 1.3.1 has no CC2540 USB Dognle driver
Hello Quinghui,Welcome to the Forum!Have you come across this post that contains a driver for Windows 8?http://e2e.ti.com/support/low_power_rf/f/538/p/243424/936331.aspx#936331Thanks,
View ArticleForum Post: RE: Blue radios BR-LE4.0-S3A or Panasoic PAN1721
I would second the lack of product support from BlueRadios, currently looking for a suitable replacement. I'll have to give Bluegiga a try.
View ArticleClik here to view.
Forum Post: TRF7970A as a reader to read RF430CL330H type 4 tag---Question
Hi, I'm working on TRF7970A. TRF7970A as a reader to read/write RF430CL330H type 4 tag, There are some questions: I have completed the type B card detection procedure: PCD---> T: 05 00...
View ArticleForum Post: RE: Coordinator software reset - network not functioning
How is PAN ID conflict defined?
View ArticleForum Post: RE: MSP430BT5190 and PAN1525 Eagle cad file support
Also here is a project I worked on(it has eagle design files) for MSP430+PAN1325A:http://launchpadlight.netai.net/design2012.html
View ArticleForum Post: RE: how can we make BLE off....
Hello Sandeep,That sounds like an interesting idea. I am not familiar enough with the WLAN RSSI to give a definitive answer, but CC2540 Bluetooth BLE device was specifically set up to avoid conflict...
View ArticleForum Post: RE: RSSI of current connection
Hi,Yes, connection is alive while scan is performed.You can use netapp_ipconfig() to retrieve the SSID you are currently connected to.Yael
View ArticleForum Post: RE: CC3000 Driver & Missed Interrupt Problem
HI,CC3000 should not be aware if you are masking interrupts or not but until the host wont lower the CS and raise it again, CC3000 should not raise the interrupt.The race described could happen, but...
View ArticleForum Post: RE: CC2540 - USB power supply
Hi Fredrik,DVDD_USB on my PCB is separated from other VDD pins.DVDD_USB is produced from USB_5V voltage (after regulator) while other VDD from the battery.If DVDD_USB is lower that other VDD, is it...
View ArticleForum Post: USB interface in CC2540
I've seen in CC2540 USB dongle kit schematics that USB_D+ is connected to P1_0 and also pulled up to VCCIs this necessary for proper USB operation?ThanksKeni
View ArticleForum Post: RE: How to do with the ANT match circuit of RF430CL330H?
Hi Josh,According to your suggest, I have achieved wifi pairing and App trigger. Thanks. :)PS: f = 2*pi * (sqrt (L*C)--------------------- I remember this formula should be like this : f = 1/ (...
View ArticleForum Post: RE: Communicating from one CC3000 to another?
Hi Alon,Do you have any update on the CC3100? I'm beginning a design and would like to design in TI if possible.Thanks,Scott
View ArticleForum Post: RE: NFC Data Rates and Streaming
Thanks again Josh, this is very interesting, really helpful information.Best regardsCraig
View ArticleForum Post: RE: BT and BTE
HI Kazola,maurizio stefani that strts the discussion about this,What I know is the capability to have a project with same HW but able to handle the two protocols (2.1/3 and 4.0) changing the FW only....
View ArticleForum Post: RE: Enabling the PCB antenna on CC1200EMK-868-930
Thanks, that's what I thought. Would it be ok to add another resistor (with the same value as R181) and disconnect the SMA antenna instead of moving R181?As a feature request, it would be nice if a...
View ArticleForum Post: RE: SPPLEDemo_Liite sometimes works sometimes not
Hi Zahid,I'm not sure how about other apps now but I found some Stonestreet One recommendations for not using the revision D due to UART malfunction when higher baud rates are used. I have tested all...
View ArticleForum Post: 400MHz Wireless Video transmission with cc113l/cc115l
Hi Everyone:I was in a project which is meant to achieve 400 MHz wireless video transmission. We were provided CC113L/CC115L trans/receiver and two TrxEB evaluation board. Yet I found from datasheet...
View ArticleForum Post: RE: Looking for the source code that ran when we got our TR7960A...
Glad I could help.If you have a LSA it might be easier to to just look directly at the SPI communication and see the differences. Thanks,JD
View Article