Forum Post: RE: CC3000 wifi example hanging after sending udp packet.
Was a type in my post. it was meant to be 192.168.1.110. But as I said it was successfully sending the packet. Once it sent the packet it then hangs.
View ArticleForum Post: CC2540, 128K flash, BLE stack 1.3.2, NV IDs for application usage?
Hi,I use IC CC2540f128, BLE stack 1.3.2, and play with simpleBLEPeripheral. At the moment my activity is around flash. According to swr194 (OSAL API) page 27 Application NV IDs are: 0x80-0xFE. But this...
View ArticleClik here to view.
Forum Post: Wilink6 different behavior between C App and wlan_cu
Hi Team,i observe following behavior during the continuous TX with OMAP3530 and WL1271, linux kernel 2.6.33It works with wlan_cu:The C application shows some error and there are no packets: Here is the...
View ArticleForum Post: RE: CC1200 4-GFSk settings
Martin,I think we figured out what was wrong. As we started adjusting the deviation, symbol rate and RBW numbers in the main window of your software, we found that we could get the CC1200 in states...
View ArticleForum Post: RE: CC3000 TCP Data Rates
Hi Troy,The highest theoretical data rate should be 11 Mbps, but when using TCP and HTTP protocols, there is going to be a lot of overhead. The highest data rate measured so far with an MSP430 (the...
View ArticleForum Post: RE: Project setup
Yes I have.I have no problems setting and using the demo projects.I was asking about starting a blank project that will use SPP in it. How do I set up the bluetopia library and all the different...
View ArticleForum Post: Restore characteristic after power cycle from flash. CC2540
Hi,Hardware: CC2540 128K flashSoftware: BLE 1.3.2, modified SimpleBLEPEripheralResources used (from map file of IAR):108 910 bytes of CODE memory 34 bytes of DATA memory (+ 82 absolute ) 6 897 bytes of...
View ArticleForum Post: RE: RF Power Output PATABLE Settings for CC430 5137
Also, if I understand correctly the data in DN013 was obtained empirically by measuring an actual chip on a pcb and would be dependant on a multitude of design factors. So if you want accurate power...
View ArticleClik here to view.
Forum Post: RE: Host control mode, CC8530+AIC3204+MCU problems, need pro's...
thank you for your enlightment, Kjetil, we tested it and found two issues and one progress.A. two issues1. the readouts of microphone bottom volume is always -15db, not the -20db as we follow your...
View ArticleForum Post: RE: Sensor Tag Released
Hello,i have a problemi connect to my senor tag try to make "Power on Self Test" but the result is 3700 not 3F00 the hardware is 1.3 1252with another sensor tag hardware 1.2 1210 the result is correct...
View ArticleForum Post: RE: Range Extender (CC2530USB) and CBKE
Ok, with Z-TOOL (USB port) we can configure Certicom Keys.
View ArticleForum Post: CC2540 Frequency tuning
Is there a way to tune the frequency of the CC2540? I know many BLE devices will have a freq_TUNE register to dial it in. If so, do you have instructions on how to properly tune the chip?
View ArticleClik here to view.
Forum Post: RE: CC254x ADC has large/variable input offset voltage
I took the data shown above. All indications from my data are that the internal voltage reference on our 115 measured samples of CC2541 are within +/- 2% of the value specified in swrs110C Revised...
View ArticleForum Post: RE: The stack 'XdataStack' is filled to 95% (4174 bytes used out...
Hello all,I had same problem and after extending XData size, no luck. Problem: when hitting download (Ctrl + D), XData reached maximum etc..The solution that worked for me: after download, go to...
View ArticleForum Post: RE: Can the Bluetopia stack for the MSP430F5438 Be Run Without A...
Hi Randy,It may be possible but it is not something we have tested because it prevents us from using the lowest possible power configuration. You can attempt this by disabling HCILL (call to...
View ArticleForum Post: CC2540 over-the-air firmware upgrade
Hello,I am trying to upgrade firmware of CC2540F256 Mini Developement Kit by over-the-air option.So far I managed to load it with BIM firmware, load SimpleBLEPeripheral .hex file via CC debugger and...
View ArticleForum Post: RE: SPPLEDemo_Lite App On MSP430F5529 Experimenter board USB...
Hi Armen ,I am also trying to build MSP430 Bluethopia sdk MSP430F5529 for CC256x but i am facing configuration issue . I am using CCS version 5 for build the sdk**getting error in console**** Build of...
View ArticleForum Post: RE: Will TI provide source code of Bluetopia stack for bluetooth...
Amit,You would have to contact Stone Street One and discuss this with them. You can find them http://www.stonestreetone.com/ -Jason
View ArticleForum Post: RE: CC2531 Android Driver Request & SDK ?
Thanks Yikai Chen, I will keep looking for more information about the topic.Meanwhile, I found a related topic that started these days talking about CDC drivers.Here's the link:...
View ArticleForum Post: pan1720 clock problem
how to set the clock for 26mhz in pan1721.i am using pan1720(cc2540) for spi communication through uart0.i configured PERCFG,P2DIR,P0SEL,P0DIR,U0CSR,U0BAUD,U0GCR as per the ti spi example...
View Article