Forum Post: RE: WL1281Q : WPS2 support in compat-wireless
Ashish, I suppose the WPS2.0 support depend upon the the hostap ( i.e hostapd & wpa_supplicant). BTW where you got the compat-wireless-3.2.5-1 and what host processor you are attaching the WL128x...
View ArticleForum Post: RE: Replace TIMAC-CC2530.lib with source code?
High in code size, but no code motion(I don't really understand what this means)
View ArticleForum Post: RE: CC1101 Optional Radio Control Feature
Hi Ushan I assume that you are referring to the optional pin control feature. This feature do not use GPIO's but the CSn, SCLK and SI pins to control the major operating states of the radio. Please see...
View ArticleForum Post: RE: iOS6 BLE Issue
Hi all, just some notes for BLE differences between iOS5.x & iOS6 (other than the disconnection thing mentioned above) .. thought it might be helpful to share: 1- default connection interval is now...
View ArticleForum Post: RE: CC2531 and CC2530 manufacturing ID
You are most welcome. Looks like you were faster to get it all working than I was. Good for you. We should be so called poster boys for TI on this. My systems using the CC2531/2530 and MSP430 micros...
View ArticleForum Post: RE: Calculating Load Capacitance for CC1111 USB Dongle Crystal
One (?) more question related to the reference design. In the BOM for the design, I see part names like these: R1 Resistor 0402 R_270_0402_F R2 Resistor 0402 R_2_0402_F R4 Resistor 0402 R_4K7_0402_G...
View ArticleForum Post: RE: Wilink8 (Com8 module) for AM335x
David, Both Murata and Jorjin have plans for SN1857 Module in Jan 2013 and will also offer a COM8 board using this module. However, as Naveen mentioned, both the modules are still in Prototype phase...
View ArticleForum Post: RE: Problems with message length
If you are using the Wireless Sensor Monitor code as a baseline, it is SimpliciTI based. The default register settings, including PKTLEN, are found in the smartrf_CC2500.h file. The SimpliciTI code...
View ArticleForum Post: RE: SimpliciTI & CC1101DK
The dev board sound like a SmartRF04 board. Try this link, it should point to some useful documentation: http://www.ti.com/tool/cc1101dk868-915
View ArticleForum Post: RE: enabling i2c in the Ez430-RF2500T application software
I don't think the SImpliciTI software was written to easily allow the sharing of the USCI between SPI and I2C, or even between multiple SPI devices. Which is why most people that have used the RF2500...
View ArticleForum Post: CC3000 FRAM Sensor Application disconnecting
I am running the FRAM Sensor Application demo as directed here: http://processors.wiki.ti.com/index.php/CC3000_Wi-Fi_MSP430_FRAM_Getting_Started_Guide_Using_First_Time_Config I am able to connect to...
View ArticleForum Post: What is the difference between destination address and...
Hello, I noticed that the descriptor request methods include zdoUserDescriptorRequest contain two parameters: "destination address" and "nwkAddressOfInterest". I've read through the code but have...
View ArticleForum Post: CC1101 and CC1110 mix
I have two CC1101 eval boards(from the CC1101DK_EM433 kit) and they work fine based on the sample projects LinkTo and LinkListen. Then I wanted to get two more but I ordered the CC1110DK_EM433 by...
View ArticleForum Post: CC2530 and CC2540 hardware compatibility
Are the CC2530 and CC2540 fully hardware compatible? I'm most concerned about pins 1->4 which in the 2530 are GND and on the 2540 are the USB interface and power. Elsewhere on the TI forums the...
View ArticleForum Post: RE: duplicate rejection
In theory, Z-stack can filter the same frame using the Sequence Number in MAC layter. But in fact , sometimes the RX may receive more frames than the Tx send. I am confused with this too. In...
View ArticleForum Post: DM8148 WL1273 support
Hello, Please let me know if WL1273 is supported for DM8148 EVM or not. Thanks, Shinji
View ArticleForum Post: TRF7960 ISO15693 Tag Inventory problem
Ｈi，Ｉ have a big problem about inventory response from the TRF7960. My system usually gets the correct UID-code. for example "00 7B 59 BC 30 00 00 07 E0". But sometimes gets the wrong number. for...
View ArticleForum Post: Port Direction and Value
I've noticed something interesting and was curious why this is happening. In the keyfobdemo app, KeyFobApp_Init in keyfobdemo.c changes some port directions during initialization. If I try to set...
View ArticleForum Post: MCPS-DATA.confirm.status = CHANNEL_ACCESS_FAILURE
hello everyone, I have a question about the ZIGBEE/IEEE802.15.4. We know when the mac layer sends a data frame ,it will obey CSMA-CA mechanism. If the channel is always busy ,channel access will...
View ArticleForum Post: RE: A possible BUG of Z-Stack Protocol.
no,i think the end device joined another router,but the pre-router saved the association of the enddevice and didn't update(clear it).
View Article