Forum Post: CC1120 calibration tables for frequency hopping
Hi,This is taken from the user manual of cc112x:"Fast frequency hopping without calibration for each hop can be done by performing the necessarycalibration at start-up and saving the resulting FS_CHP,...
View ArticleForum Post: RE: fixed transmission time
thanks. actually the data content is not important for my project. the important criteria are (i) fixed txn duration (which can be upto 500 msec) (ii) a means to determine duration at Rx end (iii)...
View ArticleForum Post: RE: RE: CC3000 Basic Wi-Fi example application for MSP430
U should enter d command in single shot and not individual characters one by one , u copy this complete.command from note pad and paste The complete command on hyperterminal or putty whichever ur...
View ArticleForum Post: cc2540 usart
Hey all,i try to get the cc2540 datasheet, and i found a broken links on this forums,plz, someone can help me with this?10x in advance,Ran
View ArticleForum Post: RE: Who trusts packet sniffer? How to make it more efficient?
[quote user="Nick L"]If you are using our device (CC2540 or CC2541) as a Wireless Network Processor (WNP), you can use the Packet Error Rate Command. Read more in the Vendor Specific HCI Guide that is...
View ArticleForum Post: cc2541 spi sample
Hey all,i m trying to make the spi sample work (of cc2541 that can found here: http://www.ti.com/litv/zip/swrc257),and i don't understand where i put this code (after compiled):on the...
View ArticleForum Post: Carrier sense threshold setting for CC1101
hi,How to generate tables for finding carrier sense threshold.In datasheet of CC1101 such tables for 2.4K baud and 250K baud are given. But how to generate similar tables for 10Kdata rate, MSK at...
View ArticleForum Post: Can smart energy profile transmit data?
Is it possible to transmit data in Smart energy profile? Say if there is a meter device which captures energy consumption and if i wish to transmit the power consumption data to another zigbee device...
View ArticleForum Post: RE: Send data from the receiver in the ACK to the transmitter
Somebody?Where I can find the block Diagram of the sofware part that send back an ACK to the REMOTE in the RempTI ? like where the RF received data is processing and then send the ACK back to the...
View ArticleForum Post: RE: TMS3705 CRC
Which one is the correct polynomial: x16 + x12 + x5 + 1 or x16 + x12 + x5 + x1 ?? Do I consider the x16? I mean,,,,,If the correct one is , x16 + x12 + x5 + 1 how do i do the XOR...
View ArticleForum Post: RE: COSMCLOUDAPP
Hi Mike, I call this routine from the main code:long http_server_update(void){long lerr; sockaddr tSocketAddr; long ulClientSocket; long SentLen; unsigned long ulServerIpAddr; char...
View ArticleForum Post: RE: How can I know that RangeExtender Device is work? for cc430
If you have a spectrum you will see this in TX. If the range extender works you will get higher power out than the CC430 normally can give for a given setting.
View ArticleForum Post: RE: Slave Host-Controlled Audio Configuration requirements?
I think somehow my problems are connected with me not talking them out enough in my head. I struggled with this problem all day yesterday and dreamed about it all night. I tried everything I could...
View ArticleForum Post: RE: Carrier sense threshold setting for CC1101
Thanks a lot Martin for your quick reply.I will try with changes in absolute threshold.Just few questions,1) How one can decide if to use relative threshold or absolute one? In our case we didn't know...
View ArticleForum Post: RE: How to test the sensitivity of cc1121
Dear TER,Can you help me to answer the last question,bacause our factory will be producing the module, thank you very much.
View ArticleForum Post: How to use DMA Flash Write and Erase?
As title.I'm trying to write a flash write routine using DAM method for my CC2510F32.My code is below:#include <ioCC2510.h>#include <ioCCxx10_bitdef.h>#include <hal_types.h>#include...
View ArticleForum Post: RE: Settings to use short preambles at high data rates on CC1120
Just wanted to thank you again, and add that although we haven't finished testing, these settings look like a good improvement on what we had before.I hope to reply further once we've got more...
View ArticleForum Post: Using the CC2510 Mini Evaluation, UART Send gibberish
I'm using the CC2510 Mini Evaluation Kit (crystal on board 26MHz)Interface UART0 @ location 1Baud rate 115.2KpbsConnection setup:P0.2 - RxP0.3 - Txtrying to capture using HyperTerminal,...
View ArticleForum Post: RE: BLE with multiple connections
Hi Nick,you are spot on, the requirements are heavy on the Central side, trivial on the Peripheral side. I've progressed with my iOS SW stack and was able to simultaneously connect to 5 TI KeyFobs...
View Article
