Forum Post: Unable to capture packet swith the Packet Sniffer + CC1110EM
Hi,I 'm using the RF04EB+CC1110EM(433MHz) with the Packet Sniffer (2.16.2) to capture packets (generic). The CC1101EM configuration was generated in SmartRF Studio 7. I first tested the setup and...
View ArticleForum Post: RE: Downloading PurePath Wireless Configurator v1.4.0
Attached, let me know when you have downloaded this and I can remove it as I do want people to use the register and download link going forward.
View ArticleForum Post: RE: cc2540 MINI DK connection interval while working with iphone...
Hi Jaden,[quote user="Jaden Ghylin102047"]Is this a limitation of the stack or the hardware?[/quote]It's a software limitation. Might be that some of our module vendors (see www.ti.com/ble-wiki for a...
View ArticleForum Post: RE: problem starting to debug CC2540 using IAR
Hi Natanel,It should be possible to get older version somewhere. Could you try IAR support? (I am looking into it in the meantime)Best Regards
View ArticleForum Post: RE: RE: CC3000 Basic Wi-Fi example application for MSP430
Hello,It's ok to run.Thanks for your help.If I want to send a file,does It also use command 04?How should I definition data length?
View ArticleForum Post: RE: IAR problem
I'm sorry, Liangliang, but 'magXYZ_AxisValue_t' absolutely must be defined somewhere else in your project and/or include files in order to suffer the IAR error that you posted. Try to make clean and...
View ArticleForum Post: 2.4 GHz Inverted F Antenna
I bought the CC-Antenna Development Kit and would like to use the Inverted F Antenna- 2440 MHz (Board #7 - DN007) with CC2530. I would like to know:1) the circuit for the matching components Z71, Z72...
View ArticleForum Post: RE: How to watch the packet from from a child passing through the...
You can intercept incoming messages in zmac_cb.c - these messages are from the MAC and they are being passed to the NWK layer code in the libraries. Look at the function MAC_CbackEvent(), and the...
View ArticleForum Post: RE: Network State not set to default in NV_RESTORE is undefined
In order for NV_RESTORE to work, you must also define NV_INITAny function that you cannot find in a .c module with the IAR global search (Ctrl-Shift-F) will be part of eithe the NWK or MAC Z-Stack...
View ArticleForum Post: RE: Supply power by pins P1_0 and P1_1?
Hi.Yes, this is correct.I want to power nordic nRF24L01+ transceiver module that is connected to OLP425. And I want to use that nordic to communicate with another nordic transceiver on another device.
View ArticleForum Post: Modifying the packet transmission rate of the EZ430 RF2500 Sensor...
Hello, I am currently starting a new project based on the EZ430 RF2500 sensors to transmit low quality audio samples through a WSN. I was successfully able to compile the demo app code and make some...
View ArticleForum Post: Configure IP parameters to the WL1271 on linux
I have an am335x evm with a WL1271 module from Murata. I'd like to configure the following IP parameters to the wlan0 device, how do I accomplish that? 1. Gateway 2. Subnet mask3. Primary DNS4....
View ArticleForum Post: RE: TRF7970 GUI hangs
Since, the problem is with everyone and also discussed on TI community!!http://e2e.ti.com/support/low_power_rf/f/667/p/130794/469569.aspx#469569A correct new version of the EVM_GUI.exe will be really...
View ArticleForum Post: RE: Dynamic AdvertData update
Sounds like a promising idea...I'll give it a try next week and update on the results.Thanks Matthew!
View ArticleForum Post: RE: Single IAR IDE Workspace for both CC2540 and CC2541
Hey Nick, thanks for your reply.Thought I'd update on my findings as well:Eventually I performed a similar solution, just the hard way: :)I diff'ed two workspaces (.ewd and .ewp files) from the same...
View ArticleForum Post: RE: Mesh Network Radio with Location
John, Check out this WL1283 based GPS WiFI: http://www.murata-ws.com/com7.htm . -Leonard
View ArticleForum Post: RE: Using the CC2510 Mini Evaluation, UART Send gibberish
Great man.So, do you developing (integrating) something for the arduino project?
View ArticleForum Post: RE: Suggestion: Make a CC4000 BoosterPack
I would love to see that boosterpack
View ArticleForum Post: RE: cc2530 / cc2531 developer help needed!
OK thanks I'll try it .. 2 questions:1) is it possible to dump info to the IAR debug log?2) when the debugger stops on a break point that's all I get ... it will never step to the next instruction, IAR...
View ArticleForum Post: RE: 2.4 GHz Inverted F Antenna
Fredrik,When I clicked on CC2533EM reference design, I got a blank page, I could not find the SWRR069.zip in TI website. Please advise. Thanks.
View Article