Forum Post: RE: HostTest App code does not fit for CC2541 with 128 Kb flash
Dear Nick,I am testing UART communication on CC2541 with 128 KB flash. I have used sample code in this directory BLE-CC254x-1.2.1\Projects\ble\HostTestApp\CC2541\CC2541EM. I have configured baud...
View ArticleForum Post: Can zigbee location system work in a nuclear power plant
I am using cc2530 to locate in the office. I know there are products using cc2530 to locate in the mine. we want to extend our location system to industrial environment (for example nuclear power...
View ArticleForum Post: RE: WL1271 Bluetooth MAC address / identifier
Just to be certain, if two devices within communication range have consecutive BT addresses, the WLAN address in the first device would have the same address as the BT device in the second device....
View ArticleForum Post: Access to the Stonestreet One’s Bluetopia+LE Stack to use with...
How do we get access and license to the Stonestreet One’s Bluetopia+LE Stack to use with the TI WL1271L (LS Research TiWi-BLE module)?We are planning on building embedded sensor device that will...
View ArticleForum Post: Access to the Stonestreet One’s Bluetopia+LE Stack to use with...
How do we get access and license to the Stonestreet One’s Bluetopia+LE Stack to use with the TI WL1271L (LS Research TiWi-BLE module)?We are planning on building embedded sensor device that will...
View ArticleForum Post: Zigbee stack for different application profile
Does the zigbee stack changes for different zigbee profile . Smart energy differes from Home automation . SE wants link keys etc . Does the stack changesdepending on profile . Does anything should be...
View ArticleForum Post: BLE Device Monitor
Is the BLE Device Monitor working with a generic BT 4.0 USB dongle (not TI CC2540)?
View ArticleForum Post: RE: Recommended antenna for CC1000
If you only get a few centimeter range something is fundamentally wrong - either in SW or HW. Refer to attached app note for debugging hints. Check Tx and Rx performance separately before you set up...
View ArticleForum Post: RE: CC3000 delivers TCP data segments out of order
An additional data point. This problem improves as I slow the SPI clock between the host processor and the CC3000 (TiWI-SL). It is pervasive at a SPI clock of 8MHz and only sporadic at a SPI clock of...
View ArticleForum Post: RE: Bluetooth Proximity Detector
That's right, Ben, BLE only. And the problem with classic Bluetooth is it uses up batteries quickly.- ChrisHttp://www.indiegogo.com/spotloss
View ArticleForum Post: CC1101 ; Sync word not detected
.Hello,I’m using one CC1101_TX as a transmitter: 868Mhz, GFSK , NO Manchester, 2 synchros words, 4 byte data, no CRC.The second CC1101_RX is configured as a receiver in asynchronous mode with...
View ArticleForum Post: RE: WOR Issue on CC1101
Hi Siri,Yes, I'm using the variable packet length, but every packet I send/receive is about 19-20 bytes size, and PKTLEN is 0xFF. And for all packets received I verify the CRC to see if it is ok. Here...
View ArticleForum Post: RE: TMS37157: problem at low range
Hello Johan.I suspect the Q factor of your "new coil" is too high (>>60?)If the Q is too high, the OOK of the request for "Page 3 will being badly demodulated and even corrupted...During the...
View ArticleForum Post: RE: ez430-RF2480
Hello Pandit! I downloaded your file, I do not understand how to run it.Sincerely, Ilya
View ArticleForum Post: RE: CC112x - TCXO output wave
Hi TERI need the same information but the link that you posted is out of date. Could you please post a revised link.Thanks MArtin
View ArticleForum Post: RE: Sleep & Wake-up on CC2541
Hi Amir,Yes, the "external events" cover button presses. It's typically a GPIO configured with interrupt, so you could essentially use any of the pins on the three ports. The power modes PM2 and PM3...
View ArticleForum Post: RE: Registering a proprietary BLE service UUID with SIG
Hi Amir,[quote user="Amir Eshel"]Since these will be commercial devices, should we register an "assigned number" with the SIG to avoid range conflicts with other devices?[/quote]You should use 128bit...
View ArticleForum Post: RE: CC25xxEM – Connectors of Evaluation Board connectivity
Distance between P1 and P2 is 1200 mils
View ArticleForum Post: RE: How to use DMA Flash Write and Erase?
Hi,everyone.Now,I can use FLASH wirte and erase by sample code(\cc1110_cc2510_Basic Software_Examples\ide\iar\examples\flash\flash.eww)But , If I use "\cc1110_cc2510_Basic...
View ArticleForum Post: RE: CC2530 Interpan and Offnet messages
hi,there is a question in my application which use the inter-pan function. as we all know that this is just equipped in ZigBee Pro,when I take a fast look at the demo SE which is supplied by TI, I...
View Article