Forum Post: RE: CRC Checksum verification -- cc2541
Thanks. I wish I had known that a few weeks ago - it would have saved me days of debugging."By posting the new addresses that you have, are you in fact confirming that your observation of this address...
View ArticleForum Post: RE: CC1110 change sleep interval in PM2
Hi Siri- If the worst thing that could happend is that the sleeptime is 128 times longer than intended, it cannot be the problem I'm looking for, since the device hangs forever!!!- I have seen the new...
View ArticleForum Post: RE: Peripheral/Observer
HelloI have exactly the same question that Dave Moelker.. now after more than a year..are there any news/change in that matter?Luis
View ArticleForum Post: CC1125 Class/Category 1
Is it possible to meet ETSI Category 1 requirments using the CC1125 at a higher data rate than 1.2KBps?
View ArticleForum Post: Packetsize PER-Test C1101 Developers Kit
Hi,i am looking for the packetsize of the Standard PER Test Firmware from the c1101 868Mhz Developers Kit.The size can be adjusted on the LCD display, but i am not sure if it is the data size or whole...
View ArticleForum Post: RE: problem connecting Zigbee Z-Stack EP to coordinator network
Hi,After some discussion with Digi they revealed the TI stack issue they were talking about:" If you are using Encryption, then try using the attached BETA firmware version which allows you to Disable...
View ArticleForum Post: RE: SPP in CC2541
1 . Of the same I thought initially, as alternative of SPP.2 . Thanks, I will look. But, I repeat, this speed - MAXIMUM, and improbable.3 . Unfortunately, the printed circuit board is already ready....
View ArticleForum Post: RE: GPRS Data Concentrator
Hi Mirco,your idea is good - you can use UART for GPRS module on TRXEB and have the wMBus Stack on the MSP430F5438A.you'll have total of 256KB FLASH memory for your GPRS control application and wMBus...
View ArticleForum Post: RE: CC1125 And Category 1
I'm looking to use the CC1125 and CC1190 in the 869.5 Band at 500mW. Before starting off on the project can you give me any information about this combinations performance for EN300220 Category 1....
View ArticleForum Post: RE: data error
OK, never mind, I solved it!I mistakenly gave the incoming and outgoing messages the same name, and then the messages got mixed up. The 1st message wasn't mixed up, that's why the first one was fine,...
View ArticleForum Post: CC2431 Dummy's guide
Hi.I've got a Chipcon CC2431 development kit (basically, 8051 SoCs), which comes with 10x CC2431, 2x CC2430 and 2 SmartRF04EB.I'm developing with IAR Workbench, and I would like to know how to program...
View ArticleForum Post: WiFi and Bluetooth coexistence
Hi all, this is a quite philosophical question, but 'im posting in this forum because i'm collecting informations looking forward to a Bluetooth Low Energy application using TI's SoC. I've found an...
View ArticleForum Post: RE: How to use TRF7970A read/write mifare classic
Vitor -here you go. you should know what to do about the file extensions once you unzip it(Please visit the site to view this file)
View ArticleForum Post: Newbie
Hello guys,i amnew at this forum..some of my friends suggest to me that this forum community is solved your problem..my problem is in My bluetoot some time it is not working i was check by the...
View ArticleForum Post: RE: CC2510 Flash program
1. How do you check that the flash becomes 0xFF? The CC Debugger reset button resets the CC Debugger, it sounds very strange that it affects the CC2510 on your target.2. [quote user="whung...
View ArticleForum Post: RE: RFID reader with TRF7960 and PIC24FJ128GA010
Javi -did you try setting the Chip Status Control Register to (for example 0x21) and then ISO protocol register to (for example 0x02) and then sending the inventory command?0x8F, 0x91, 0x3D, 0x00,...
View ArticleForum Post: ADC to radio to PC, int (int16) to char (uint8) and back to int...
Hi, I am trying to write a code to ADC a sine wave and then radio it to a cc2511 dongle acting as a serial port to a PC, so that I can plot and re-create the sine wave at the PC. Now I am really...
View ArticleForum Post: RE: CC3000 delivers TCP data segments out of order
I have encountered this same issue. I am sending large files via TCP during an HTTP session and I see packets being transmitted out of order. This is unacceptable. Attached is a copy for a Wireshark...
View ArticleForum Post: ADC to radio to PC, int (int16) to char (uint8) and back to int...
Hi,I am trying to write a code to ADC a sine wave and then radio it to a cc2511 dongle acting as a serial port to a PC, so that I can plot and re-create the sine wave at the PC. Now I am really getting...
View ArticleForum Post: RE: Texas Instruments BLE Stack 1.3 Released
Nick, this is exciting stuff. I was getting antsy waiting for this news.Can you tell me about what was addressed in 1.3 regarding this bug: http://e2e.ti.com/support/low_power_rf/f/538/t/227515.aspxMy...
View Article