Forum Post: TRF7960a TB: Voltage regulator issue
Hi everyone,I bought several month ago a TRF7960a TB, that I interfaced at this time with a ezdsp 5535 board. It never worked, and afterinvestigation, I found that the Vreg TPS61222 was not giving me...
View ArticleForum Post: RE: Packet format in ASK/OOK modulation with continuous...
Ok, if you want to just send power your register settings look good. From what I can see from your settings you have programmed to send a CW (unmodulated carrier wave).If you use the 'continuous TX'...
View ArticleForum Post: RE: WL12xx SDIO issues when Bluetooth Enabled.
Just a follow up to this issue. I have decided to do some more tests.I have disabled the CONFIG_TI_ST and the WIFI worked fine. I did the following command from the console:cat /dev/ttyO1When I checked...
View ArticleForum Post: cc2541 Limit OSAL support needed
Hey all,I'm using cc2541 on smartRF05-EB, using OSAL provided.I want to use just the BLUETOOTH LE and the USART1, nothing more, and i want the OSAL will support just that.Can someone plz help me which...
View ArticleForum Post: RE: WiFi calibration on wl1271
Krt,I am moving this thread to the WLAN Applications Forum to better answer.Regards,Gina
View ArticleForum Post: RE: Universal Boot Loader issue
Hi George,The UBL project is released in the 1.3 stack release, Projects\ble\util\UBL\soc_8051\usb_msd\iar.To make a .bin file for UBL, please refer to the build options (ALT+F7) when the build...
View ArticleForum Post: RE: BloodPressure app on cc2540 mini keyfob
Hi Has anyone made the bloodpressure demo to work with keyfob+dongle setup or smartrf setup? If yes, could you please help me ?ThanksBiswa
View ArticleForum Post: RE: Connection Interval inquiry
Hi George,If you wish to send data quickly from the sensor when relevant but save power, use slave latency to skip some of the master's connection events. If you wish to send data quickly (low latency)...
View ArticleForum Post: RE: Can't detect CC2541 project with anything other than TI dongle.
Hi guys,Thanks for your responses.We used the TI BLE Multitool app on iPhone (and the native Bluetooth controls on Windows). I'll give LightBlue a try.We developed a custom project but when we were...
View ArticleForum Post: RE: TI evaluation-board for PSK and/or FHSS
Andre, I do not know the Dolphin kit you have found, however for the CCx series products have a release of SimpliciTI 1.2.0 that includes FHSS. It only supports a limited number of devices so read the...
View ArticleForum Post: RE: CC2540MINIDK_EM, read UUID error
Other test:1. with the iOS App "TI Bluetooth Low energy Multitool" on iPhone5, the Keyfob (CC2540MINIDK_EM) works fine !!2. by "TI Multitool": Services discovered --> several UUID found:...
View ArticleForum Post: cc2420 address recognition
Hello, I'm using CC2420 chips on a university research project. I'm having a small issue with the hardsware address recongnition system. It works fine at PAN level but it does no filtering at short...
View ArticleForum Post: RE: Searching crystal for CC1110 mounted in SmartRFCC1110
I have the same problem in trying to find this 26MHz crystal oscillator (part no. C5S-26.000-16-1010-R).Is there any particular reason that TI uses this oscillator on the development kit? Will any...
View ArticleForum Post: RE: Headset Dev Kit - Audio lags with USB
Thanks Kjetil!I verified your solution immediately today and it works!I am now able to set the Slave -> Master received volume and even the MUTE tickbox in the USB_soundcard functions.This helps me...
View ArticleForum Post: RE: IAR for cc2540
Thanks Jonathan.Would it be allowed to use the sample hex's in a production product? All I need is to connect and read the RSSI.
View ArticleClik here to view.
Forum Post: RE: CC2540 antenna
I am trying to be as precise as possible when implementing the antenna from the app note. I can find all the dimensions in the table, except one. See bellow.I am assuming the two fingers are equal, and...
View ArticleForum Post: RE: I'm seeking a recommendation for a sub 1Ghz protocol with low...
Dear TA12012:SmartRF Studio doesnt offer extensive settings provides via checkbox, list menu etc. Only basic settings I think. For example, it has "code examples" to different speed and optimization...
View ArticleForum Post: RE: Anyone see this linker error when attempting OAD in BLE stack...
Aslak,Thank you very much for the full explanation. I have OAD running and tested using the TI iPhone app. It seems to work well.I do have two followup questions.1) Does the OAD service indicate...
View ArticleClik here to view.
Forum Post: RE: serial application cc2530
Dears,You can set it in Preprocessor tab which is located in project optios.
View ArticleForum Post: CC3000 scan
Hello,I use MSP430F5438 to link CC3000.I have some questions.1.I want to Auto Connect AP, so I set wlan_ioctl_set_connection_policy(1, 0, 0).But it still type ssid to connect AP.CC3000 can not Auto...
View Article