Forum Post: RE: CC2560 hopping sequence for Japan
Hello Miguel,Still waiting on this information from the customer. I will post when I get it.Thanks,Ryan
View ArticleForum Post: RE: eZ430-TMS37157 Development Board -- RFID Demo Software 1.4.3
Shell,In the event you cannot secure the TMS37157 solution (sorry, I cannot comment whether it is no longer productized or not, but interestingly Digikey has stock of the actual TMS37157 device)...
View ArticleForum Post: YmsCoreBluetooth v0.94 released - Supporting iOS and now OS X.
Announcing the latest update to YmsCoreBluetooth, a framework for building Bluetooth 4.0 Low Energy (aka Smart or LE) iOS or OS X applications using the CoreBluetooth API. Includes Deanna and...
View ArticleForum Post: RE: SPPLEDemo_Liite sometimes works sometimes not
Hi Zahid,I'm using CCS 5.3.0 with TI compiler v4.1.2.
View ArticleForum Post: RE: Streaming Audio from PC
Thanks for the direction Miguel! The EVM kit looks to be a very good starting place...
View ArticleForum Post: RE: CC2520 internal frequency sampling GPIOs
Adrian, I do not think you are seeing any jitter due to the speed of the IO's, it is more likely that your jitter is coming from the correlation engine inside the CC2520 is trying to make a decision on...
View ArticleForum Post: RE: Modifications of CC1125EM-CAT1-868 board for 902 – 928 MHz band
Customer Update: We realize that the spectrum analyser is being overdriven in the plot that shows the "mound" of broadband noise between 120 and 1250 MHz, and have considered whether the mound is...
View ArticleForum Post: RE: CC1125 = CC1120 = CC1200 at certain config?
GGA,The CC1200 is a new design, the others as you state are closely related and you could consider more like speed grade binning./TA
View ArticleForum Post: RE: Re cc1101 spurs when connected to a 1 watt power amp
I have now changed crystals I tried a 26.451 MHz and a 27 mhz and still getting spurs the only chip power up is the cc1101 please see attached spec an pdf
View ArticleForum Post: RE: CC2540/1 mini DK interface with MSP430?
I don't think there is any published code to work the CC2541 from the MSP430.You could start with following as a starting pointhttp://processors.wiki.ti.com/index.php/LPRF_BLE_SerialApp
View ArticleForum Post: RE: WL12xx configuration in board file succeeds, but there is no...
Hi Kobi,Thanks for your response. I am fairly certain I have the GPIO configuration correct. My pin mux settings are as follows:static struct pinmux_config wl12xx_jaguarshark_pin_mux[] = {...
View ArticleForum Post: RE: Multiple antennas, single RFID reader IC
I'm blown away!!! Thank you so much!Few questions about this design:1. Will it be feasable to implement also on ISO 14443 protocol? (as I wanted to use the lower cost TRF7963A IC which does not...
View ArticleForum Post: RE: CC2530EM Programming through debug interface
Hello all,Glad to inform that I have found the solution for above discussed question. It goes as follows:1. Connect USB_DBG_DD to DD pin of CC2530.2. Connect USB_DBG_DC to DC pin of CC2530.3. Connect...
View ArticleForum Post: EK-LM4F232 + CC3000EM + SCAN AP
Hi, I am using the basic WIFI example, and I am not sure if the EK-LM4F232 is communicating with the CC3000EM, what command can be used to test the communication? How to use the function:...
View ArticleForum Post: RE: Minimum clock rates for CC2564/MSP430
Hi Joel,The lowest UART our device supports is 37.5kbps, default is 115.2kbps. The lowest clock rate on the MSP430 we support is 8MHz.
View ArticleForum Post: RE: about CC2541
thank you a lot!!i will try again,sorry my English is very poor , thank your help, it's very useful for me. .
View ArticleForum Post: RE: Help with MSP-EXP430F5529
My apologies for delay in replying. Thank you for the help. That is what I was looking for.
View ArticleForum Post: Creating a Timer for Data Throughput Question
Hi,So I was wondering how to implement a timer on the time it takes for the packets to send from start to finish on the data throughput example. I am using an iOS device as the client and wasn't sure...
View ArticleForum Post: Stuck in erroneous connected state
When we have a BTLE client running for some time, repeatedly connecting, reading the attributes, and getting disconnected, eventually the Stonestreet/TI/LSR system gets into a messed-up state. When in...
View Article