Forum Post: RE: Is it possible to measure with 0.1MHz?
Hello Robert,The throughput limitation is pretty much a CoreBluetooth BLE limitation and that of the TI BLE Stack. You may be able to squeeze more out of it using some experimental method, but at this...
View ArticleForum Post: RE: RSSI and TX Power info in CC2540/CC2541
Hello Alex,The Proximity Profile contains all the information pertaining to RSSI and TX power. There are sections of the Keyfob and Peripheral examples that tests these parameters (_ProcessEvents,...
View ArticleForum Post: RE: RI-I16-114A-S1 unique ID, can it be shorter?
Joshua - pls. see attached for the meanings of every byte in a UID. I think that you will find that your suggestion is possible, as two bytes of the UID are not unique and one byte is not unique in a...
View ArticleForum Post: RE: TRF7970evm+MSP430FG4618: connection issues
Guys, I feel like I'm being ignored here, and I know that my questions are no challenge for you...so please
View ArticleForum Post: RE: CC Debugger IAR Crash
Thanks, I've never done that but I'll give it a try. I'm using VS express, hopefully it's not defeatured too much... I think I'm going back to IAR also. My workaround is to compile with IAR, load...
View ArticleForum Post: RE: cc2540 flash memory
You can look at the .map file to see how much RAM and Flash you have available and then go back and adjust your code. I believe the OSAL NV provides 3K of user Flash. There is also one of the sample...
View ArticleForum Post: RE: cc1110 UART transmission problem
Alejandro Vicente,Our devices are UART devices and not RS232 devices, the difference is the voltages used. UART uses standard CMOS level (0-3.3V) where RS232 uses differential -5V to +5V voltage. You...
View ArticleForum Post: RE: AES128 sample code in C for C1110 / CC2510 (still important)
Jo, As TER said in a different post we had to remove that app note due to export regulations. Have you tried to perform a quick "Google" on the app note name or some of its content. There are many...
View ArticleForum Post: RE: CC2540 and STM LIS3DH
Hello Andrea,I haven't used this device in SPI mode, but the LIS331DH in i2c mode. Make sure that the CS pin is low when the device is powered, otherwise it will be in i2c mode.Thanks,
View ArticleForum Post: RE: CC1125 with AX25 protocol and CW
Hello Mike,I don't know the answer to your question. This is something I have been curious about so I'm going to tag along on this thread for research to a very distant project.Thanks,
View ArticleForum Post: GATT Properties - Handle
Hi,Im looking over the SimpleBLEPeripheral project, and I'm looking at the simpleGATTProfile.c/static gattAttribute_t simpleProfileAttrTbl[SERVAPP_NUM_ATTR_SUPPORTED] array.I don't understand the...
View ArticleForum Post: RE: Need a favour from some kind soul...
Thanks for the help. Appreciate it!
View ArticleForum Post: RE: WL8 + AM335x 40MHz Channel Bonding/MIMO
Victor,Thanks. I am still testing all of this. Do you know whether I can enable SISO40 in 5GHz?Regards,Gustavo
View ArticleForum Post: RE: TIWI5 chip: Add Bluetooth support in AM3505 (AM35xx) board...
Hi Jignesh,Can you provide the commands you entered and messages you saw?
View ArticleForum Post: RE: cc2530 High Impedance pin ?
Thanks for the information .. appreciate it!
View ArticleForum Post: RE: rf2500 & CCS v5 nightmare.
Hello,Did you solved that problem?LidiaHola,He visto que estabas probando el mismo código que yo. Tengo el mismo problema. Mi pregunta es si conseguiste solucionarlo y conseguiste que ambas tarjetas se...
View ArticleForum Post: Frequency agility
Hi, everybody!I have a problem and maybe somebody can help me with. I work with ez430rf2500 development kit. I need to make 2 sets kind of remote systems. Set consists of Access point and End device....
View ArticleClik here to view.
Forum Post: RE: Range question - 10mW/433Mhz vs 1W/915Mhz
Ric, If your system can afford the power required by the power amplifier going with more power will give you better results long term. We have a nice app note on estimated path...
View ArticleClik here to view.
Forum Post: RE: CC2540 and STM LIS3DH
Here are some scope data of:Write at 0x20 value 0x47 ( first 16bit)Rread register 0x0F|0x80 (first bit has to be 1 to read).(purple MOSI green MISO)Data sent to the accelerometer seem to be valid but...
View ArticleForum Post: RE: meandered inverted F-Antenna design
Hi Asaf,2) They should be place as close to the antenna as possible. Both the series and shunt components are for the possibility that you need to shift the antenna impedance. Have a look at this...
View Article