Forum Post: RE: Soldering exposed pad of CC1110
Thanks so much for your helpful input. I will try it and see if the issue can be fixed. I believe it will. Thank you !!
View ArticleForum Post: RE: EZ430-RF2500 Battery?
[quote user="Raghu Guttula"]1. I need an output voltage of 6v but the unit out put of EZ430_RF2500 is only 3v . so how i can overcome this???[/quote]If you need to generate a 6V output, then you will...
View ArticleForum Post: RE: Right GPIO pin for TMDXEVM8148 Evaluation Module (Rev D) to...
Santosh,Which GPIO you are using and is it connected from processor to WL1271 module - is there a way you can probe if this IO line is pulled high when you try to turn BT On? If not then it explains...
View ArticleForum Post: RE: Does wl1271's revision matter?
Alexander,Are you facing issue only with calibration? Does basso operation on/scan/connect to AP is functional for you?Regards,Naveen
View ArticleForum Post: RE: sample codes and how to understand RF module cc110l rf...
HiPlease see the following post for example code for the CC110L:http://e2e.ti.com/support/low_power_rf/f/156/p/223754/787859.aspx#787859
View ArticleForum Post: RE: WL1271 FM Power Level Question
Chris,Please note the relation between dBm to dBuV relationship --97 dBuV = approx. -10 dBm128 dBuV = approx. -21 dBmFor measuring the TXC output power - Disconnect antenna and measure TX output power...
View ArticleForum Post: IAR Debugging : Break points
I'm working on CC2510 using IAR 8.10 version + CC_Debugger.I'm placing break point, and I can see that the program is being executed, but didn't stop at my BP.It does stop inside main(), but stop...
View ArticleForum Post: RE: OSAL USB initialization and callbacks
Hi Eng351, thanks for the feedback. The hardware I am using is the USB-Dongle. As to whether my code is handling the USB pull-up correctly, that is (was) a no. After doing further troubleshooting over...
View ArticleForum Post: RE: CC1101 Ground die
- Have you tried to set the CC1101 in TX to see if the spectrum is as expected on the failing boards?- Are you sure that the failures comes from poor grounding? The gerber plot you have included looks...
View ArticleForum Post: RE: TRF7970A SPI without SS = Problems to read Mifare in direct...
Hi Jorgen!it seems that you have already achieved using SPI mode, !Could you please show me how to change the trf7970a from direct mode to SPI, except for the way described in trf7970a evm user guide...
View ArticleForum Post: Any cosine pulse shaping applied in CC2xxx chip?
Our experiment shows the multi path fading is the key factor in indoor zigbee communcation. I would like to know whether there is any mitigation in chip level, such as cosine pulse shaping? or other...
View ArticleForum Post: Debugger-Faild on LM3S9B96
Hi all, in my Project i use a Keil uVision (v. 4.60.0.0) and a Keil ULink2-Jtag-adapter. The Jtag is only connected to one LM3S9B96. The Debugger detect an ARM CoreSight JTAG-DP (IDCODE 0x4BA00477;...
View ArticleForum Post: Difference between controller and module
Hello,I am rather unfamiliar with Bluetooth applications and would like to use one that will transmit audio information to a Bluetooth headset with the MSP430BT5190.However, I am confused between...
View ArticleForum Post: RE: Unreliable wlan_connect()
Back when I had the CC3000 connected to the MSP430 board, I did have some problems connecting, but I didn't have the logic analyzer connected so I can't say for certain that it was the same thing. If...
View ArticleForum Post: RE: Steps involved in applying a patch on CC3000 device?
Bharat,Does this answer your question?Regards,Abhijit
View ArticleForum Post: serial app + cc2531+USB
As suggested by Dirty Harry in this thread, I have downloaded the serialapp for cc2531 from the link. I think this app uses UART for serial communication. Is there any example available which uses USB...
View ArticleForum Post: RE: UART Bytes missing with ISR
Hi Nick,Good news to me, too.Would you please let me know the new version release schedule?Thank you.
View ArticleForum Post: CC2500 STX and SFSTXON commands
What is the difference between the STX and SFSTXON commands?The Frequency synthesizer part is a bit confusing in the state diagram. STX starts up freq synthesizer, calibrates it and turns it ON &...
View ArticleForum Post: RE: Connection disrupted after connection parameter updates
Hi Jun,I don't have much experience with the T.I. protocol sniffer so it's hard for me to tell exactly what is going on in your captures. In my case, the LL_CONNECTION_UPDATE_REQ was received, but no...
View Article