Forum Post: RE: 6LoWPAN network without edge router
Hi, Jonas,As you mentioned, the data exchange between two nodes has to go through the Edge Router, how did you test the communication distance of 800m between two CC430 nodes? Does that mean there is...
View ArticleForum Post: CC8530 Audio Reset PP output performance
Hi,In the PurPath Configurator there is a signal GIO2/Audio Reset in the IO section.I believe this is an output from the CC8530. How does this output perform? Does it hold reset when the radio is not...
View ArticleForum Post: RE: CC1101Q1
Hi Jerry,we reduced some overlaps at our development kits, therefore you can also use the std. CC1101 eval kit:http://www.ti.com/tool/cc1101dk868-915Functionality should be the same as with the...
View ArticleForum Post: RE: Problem with router. How to increase distance between...
Hi Tamachi,[quote user="Tamachi Lee"]My sniffer, which stands near coordinator does not shows any activity from end-device.[/quote]How if you put your sniffer on the router which is the parent of the...
View ArticleForum Post: RE: controlling the number and size of ACL data buffers
Sure. It's a long description, but I'll try to be as brief as possbile.For our application, our mobile terminal (with the DM3730 host processor and cc2567 radio) is the master of a piconet with a...
View ArticleForum Post: RE: cc1101 continues to report of CRC errors and garbage data
Hi,Have you solved this problem?I wonder to try similar thing to apply 868MHz interface, may be also cc1101, to the Gumstix board. Could tell me how to install CC1101 on overo-gumstix board?Thank you!
View ArticleForum Post: RE: CC2540DK and Motorola
Hi Peter,Thanks for your reply, I have not updated and my phone still says Android version 2.3.6However, I am trying to run the Motorola_BLE_API_sample2 application, and also make my own application...
View ArticleForum Post: RE: Can we lower down chip rate of DSSS in order to mitigate the...
Hi,Any Zigbee device should comply with IEEE802.15.4 standard and the usage of DSSS modulation at 2.4 GHz is inevitable.Moreover, the spread spectrum signals (the DSSS is just one of possible...
View ArticleForum Post: RE: CC3000 MSP430 kit not set up right?
Hi Brandon,9600 Baud still does not work. LED5 comes on first then LED6 comes on but the board will not communicate with TeraTerm or HyperTerm.The CC3000 Patch Program says that it completed with no...
View ArticleForum Post: RE: Any cosine pulse shaping applied in CC2xxx chip?
Hi,just look at Std IEEE 802.15.4-2006 clause 6.5.2.5 (Pulse shape).Regards,Ilya
View ArticleForum Post: TIWI-SL CC3000 Wifi module GPIO problem with c5515 usb stick
I am trying to run LSR TIWI-SLCC3000 wifi module with c5515 usb stick. To start wifi module, PWR_EN bit of cc3000 is required to set to '1'. PWR_EN pin of wifi module is connected to GPIO 4 pin of...
View ArticleForum Post: RE: C5515 EVM Wi-fi application
I am trying to run LSR TIWI-SL CC3000 wifi module with c5515 usb stick. To start wifi module, PWR_EN bit of cc3000 is required to set to '1'. PWR_EN pin of wifi module is connected to GPIO 4 pin of...
View ArticleClik here to view.
Forum Post: How to test the sensitivity of cc1121
Hello,I have a problem when I was testing the sensitivity of cc1121,the frequecy of my cc1121 module is 469.995MHz,if the frequecy of generator is set to 469.995MHz,the sensitivity is...
View ArticleForum Post: RE: Set data to UART using CC2540 based board?
yes, there are. Look at the following:Hal_UART documentation in the hal folderthis thread: http://e2e.ti.com/support/low_power_rf/f/538/p/218578/771521.aspx#771521and the serialApp code in the wiki
View ArticleForum Post: RE: Packets from CC1101 on custom board not picked up by packet...
Also make sure the capacitive loading on your crystal is correct. Accurate frequency is very important on these narrowband designs. You could also try setting your board to continuous TX and the TrxEB...
View ArticleForum Post: RE: CC1190 with CC430 and Johanson Technology Matched Balun Filter
The newer version of the ez430-Chrono watch design uses the JTI balun if you want to look at another reference design.
View ArticleClik here to view.
Forum Post: RE: The interoperability of Z-Stack(2.5.1.a) and Ember
Hi Andy,In Z-Stack 2.5.1a, it does support active endpoint request/response, simple descriptor request/response and end device bind request/response.If you want to send these request to other nodes,...
View ArticleForum Post: RE: WL1271 NVS file format
Eyal,I have another customer interested in this document. Would you mind sending it to my email?
View ArticleForum Post: RE: CC debugger 2540 programming works in smartrf GUI but not...
Øyvind, This works! Thank you so much for getting us a copy so fast! Brilliant! I will watch for a new release in the near future and use what you sent in the zip until then.
View ArticleForum Post: RE: UART Bytes missing with ISR
Hey Nick,Sorry to keep harping on this topic, but i was wondering if you or someone else on the TI team could share any more details regarding this issue.The peripheral I am working on uses significant...
View Article