Forum Post: RE: ISTACK oveflow?
when I got this msg, I checked real time stack usage and it is far from overflow. I believe somehow I enter into sleep mode using debug mode. And the debugger got reset. wonder whether it is a...
View ArticleForum Post: problem capture rising and falling edge
i want to capture every edge in pin P1-2 wich used GPIO as INPUTbut the registre PICTL can only be rising or falling edge and not twice at the same time !!??I Can't capture rising and falling edge at...
View ArticleForum Post: FPGA Control of CC3000
I am looking for a document that gives the control functions for the CC3000 at the register level. I am trying to implement the control functions without an embedded processor. I need the actual 1's...
View ArticleForum Post: RE: How to get 2-byte PANIDs of nearby networks to be able to...
Hi Derek,for the same goal I use ZDO_NWK_DISCOVERY_REQ/ZDO_BEACON_NOTIFY_IND commands. It should be noted that going this way, the node must be out of any network to start the process of...
View ArticleForum Post: LogicPD as AP
HI, I have logicPD eval board ( OMAPL138 ). When i try to set as AP, i followed the steps mentioned in the below...
View ArticleForum Post: RE: Strange behaviour on CC1150 and I need urgent help
Hi Siri,Thanks for quick reply. I was calculate and fill PATABLE. But I was pushed values to 0x3F instead of 0x3E. I was check several times but I was could not see.:DSo values writen to TXFIFO not...
View ArticleForum Post: RE: Join the effort to port Contiki to CC2530 and using the SDCC...
Jonas, thanks very much for the info. Your CM3 based device is certainly attractive. What are the anticipated timescales for achieving the port and how best can we keep in touch with progress? Key...
View ArticleForum Post: RE: Unable to receive notifications at correct frequency
Hi guys,I would really appreciate some help on this issue.Perhaps a simpler question would help.How do I change simpleBLEPeripheral such that SIMPLEPROFILE_CHAR4 is sending its notifications at 20...
View ArticleForum Post: CC2543 / 2544 Radio Frequency Synthesizer Calibration
I am trying to find out any sort of timing information on the frequency synthesizer calibration / lock time for the CC2543 / 44. The current docs make no mention that I can see about this, the closest...
View ArticleClik here to view.
Forum Post: RE: How to change to 200kbps BW configuration of CC1120 from your...
The noise floor becomes higher about 50dB not just 10dB. The reproduction ratio with CC1120EM is not so high. However, it's easy to reproduce the problem with CC1120+CC1190EM.Could you please try the...
View ArticleForum Post: CC2500
Customer using CC2500 module from QUASAR with PIC MCU.When regarding trying to read Rx FIFO regisdter,no data was found.It was design according to tjhe state machin rtecomendation at the d/s.(Please...
View ArticleForum Post: RE: Need help: RSSI in synchronous serial mode for CC1101
HiThe radio will be able to find the sync word. We usually refer to the 0xAA part as preamble and the the following bytes(0xD6 in your case) as sync word. I understand that both our preamble and sync...
View ArticleForum Post: RE: cc2511EMK rf_modem
Hi, thanks for the reply! The .map file says: 17 202 bytes of CODE memory 25 bytes of DATA memory (+ 30 absolute ) 1 522 bytes of XDATA memory 64 bytes of IDATA memory 8 bits of BIT memoryErrors:...
View ArticleForum Post: IEEE Address Selection
In the Z-Stack User's Guide-CC2520 (SWRU165) I read:"Every ZigBee device requires a unique 64-bit IEEE Address. Z-Stack uses the following three-level hierarchy to determine the IEEE address."1.- Read...
View ArticleForum Post: ZCL and MT
HiHow can I use ZCL with MT or which subsystem in MT is related to ZCLThanks
View ArticleForum Post: RE: Problem sending data to connected End Device from Coordinator
[quote user="Dh Sh"]Hey,my problem looks very similar to yours. Basically I am using DemoApp (from samples) and trying to send data from co-ordinator to sensorEB. I have added out cluster command on...
View ArticleForum Post: RE: Question regarding LNA CC259x
considering we have both battery powered device and main powered device, we probably will apply LNA only to main powered one. so I am a little bit worried about the asymmetric link issue.Rui
View Article