Forum Post: RE: CC1101 to CC1125 link
Hello and thanks for the reply, I modified the 868MHz board in the following way: Replaced all the passive values to conform to the 433EM reference design, With few minor exceptions, 5.1pF capacitors:...
View ArticleForum Post: RE: Zigbee Stack Development
HI denisFirst of all i wish to congratulate and thank you & your team for Zboss. We are trying to develop a zigbee stack for LPC series . We are still in infant stage though .IF i may ask how long...
View ArticleForum Post: CC2540 Mini kit - making the keyfob discoverable
Hello, It seems I got one of the very old mini kit versions (March 2010) I ordered it from Farnell. Anyway, I managed to get over the issue with the battery and constant beeping of the kit....
View ArticleForum Post: RE: Enabling security in Z Stack 2.5.1a in SE profile
hi,help! I had failed to applying for a Certicom ZigBee SDK License twice ,i don't have a e-mail address format that they required,anyone can sent me a copy of ECC library,please ,...
View ArticleForum Post: static analysis
can someone what is the setup time and hold time of cc1101 for both read cycle and write cycle it wasnt mentioned in data sheet prorerly
View ArticleForum Post: CC2540 battery
All the projects utilising the CC2450 seem to based around the CR2032 coin cell. Is there any drawbacks, apart from reduced cell capacity, in using a CR1632 coin cell instead of the CR2032.My project...
View ArticleForum Post: RE: bluetopia, how to response pin code automatically?
Hello,I am using MSP-EXP430F5438 and PAN1323ETU. Even I want to enter pin code "0000" automatically to connect PAN1323 to my PC. I carried out steps as you mentioned above but still I get message on...
View ArticleForum Post: RE: TRF7970 ISO14443B at higher bit rates
technically - the ATTRIB command is what is sent by the PCD to indicate that DR should be changed, and the Answer to ATTRIB (from the PICC, at the starting DR) is what is telling the PCD that the card...
View ArticleForum Post: RE: TRF7960 dual input AM/PM receiver + bit collision position...
the DSFID byte is not considered to be part of the UID...so therefore no collision should be indicated if two DSFIDs are the same. (in fact they all start out the same = 0x00)
View ArticleForum Post: BT 2.0 and BLE coexist in CC2564?
I want to know if I can have two stack BT 2.0 and BLE runs in the same time for one Chip. The thing I want to accomplish, I want to support BT 2.0's profiles like headset profile, in the same time, I...
View ArticleForum Post: RE: How to read RSSI using CC2530 mini kit
Bump .I am trying the same thing , I am using the AFZDO simple example, are there any ZNP command that can be sen to the cc2530 to request the RSSI value, or is there any other way . Pls help us...
View ArticleForum Post: RE: CC debugger flash programming worng content
(Please visit the site to view this file)Dear Sir,I found the different address in the middle of the firmware code, like the attachementEdwin
View ArticleForum Post: RE: Bluetooth antenna orientation.
Just to simplify things, if you have two antennas of a particular type - in this case chip antennas mounted on circuit boards - and these antennas are physically oriented the same way (i.e. their tops...
View ArticleForum Post: Message Response Timeout
I'm having an issue with the CC2540 development kit that only seems to have popped up recently.Whenever I write a a configuration attribute, the value is written BUT I then receive a timeout message...
View ArticleForum Post: RE: Message Response Timeout
[quote user="TielmanT"]Ok, I tested it the other way around as well. Old stack FW 1.2.1 on controller and new BTool 1.3...fail! So, BTool 1.3 fails with both versions of the Stack running on the...
View ArticleForum Post: RE: End Device can't receive data
Hi, Do you know if it is possible to switch on Power Saving mode and go back to Poll Mode and no Poll at all during run time even if I choose to set DRFD_RCVC_ALWAYS_ON=TRUE in the config file?...
View ArticleForum Post: RE: Ed with no sleep
Hi, Do you know if it is possible to switch on Power Saving mode and go back to Poll Mode or even no Poll at all during run time even if I choose to set DRFD_RCVC_ALWAYS_ON=TRUE in the config file?...
View ArticleForum Post: RE: help in (hal_types.h) file
Hi, I using MSP430F5436 and C1101 with Code Composer Studio Software. I am facing same problem . It says error on "unsupported compiler". I tried with ' IAR MSP430 workbench ', it works fine. Give a...
View ArticleForum Post: RE: question about end device polling
Hi YiKai, I tried you suggestion and no luck so far. It looks like if I set DRFD_RCVC_ALWAYS_ON=TRUE in the f8wConfig.cfg file, the End-Device Joins the network with RECEIVER_ON_IDLE capabilities....
View Article