Forum Post: Manufacturer ID
For a long product life cycle design using CC8530, is there a way to create the MFG. ID without the "golden" radio / configurator combination? If that radio is damaged, erased, or fails for some...
View ArticleForum Post: CC2540
Hi I have a number of queries relating to the CC2540 processor.In the users section it states that the digital I/O on the CC2450 can be programmed for tristate, pull up or pull down. Are the resistors...
View ArticleForum Post: RE: CC2540 USB Dongle not work with BTool 1.3
Hello,The driver is located in the BLE 1.3 release folder, ..\BLE-CC254x-1.3\Accessories\Drivers\usb_cdc_driver_cc2540.infReinstall the driver by browsing to this location.LPRF Rocks the World
View ArticleForum Post: How to configure BLE to do fast burst communication?
Hello:I am trying to optimize the Low Power RF Bluetooth application to do fast burst communication. Using the CR2032 coin cell battery, I cannot have the device to stay power ON too long. I would like...
View ArticleForum Post: CC1101 Features
HiI am quite new to the RF world and wanted to know some (hopefully) basic stuff about the wireless capability of the CC1101 modules. I am planning to design a wireless system with multiple nodes to...
View ArticleForum Post: RE: CC2540 battery
This paper might be interesting to you if you have not already read it:Coin cells and peak current drawLPRF Rocks the World
View ArticleClik here to view.
Forum Post: RE: Connection terminated reason 8
Please find below the logThe parameters on the central are the same as those in the peripheral. I appreciate your help.
View ArticleForum Post: How can I configure the ZStack-LM9B96-2.5.1 to work with Z-Tool?
It's my 3rd post about the Stellaris Z-stack and my question is always the same. I'm using the DK-LM3S9B96 & CC2520EM for testing the Z-stack.However, I cannot advance my experience for...
View ArticleForum Post: RE: CC1101 : Query regarding PQT algorithm
The counter will not go negative. 0-1-0-1 will give a count of 3, if a 1 is next received the counter will be reset to 0.
View ArticleForum Post: UART Configuration trouble
Hi All, First post, be merciful. I have CC2540-MINI keyfob setup, IAR 8.20 with 1.3 BLE Stack . My goal is to setup a simple UART communication link. I studied DN112 to familiarize myself with UART...
View ArticleForum Post: CC1111EMK868-915 Can't Flashing Using CC Debugger
Hello Everyone, I'm trying to flash a firmware image onto my CC1111EMK868-915 using a CC Debugger. I followed the instructions for updating the firmware on the CC debugger and everything updated...
View ArticleForum Post: RE: Open Source Compiler for CC2540
@ 1960865 I disagree. Apple sells phones, not software. Imagine where iPhone would be without XCode. But hey, we don't need IDE, we need a compiler. Ti sells cc2540 chip without a compiler or some...
View ArticleForum Post: RE: Why does the TRF7960A EVM turn on with both EN and EN2 pulled...
Henrik -I think you are confusing EN2 with EN...EN is tied to ground on the EVM through 10k, EN2 is tied to GND through 0 ohm jumper resistor (on HDR_2). if its not too much trouble - please confirm we...
View ArticleForum Post: RE: zsensormonitor.exe not found
Hi,you can find the sensor monitor.exe at this link http://www.ti.com/litv/zip/swrc096eThanks,TheDarkSide
View ArticleForum Post: RE: cc1101 crystal oscillator
The SLEEP current will be affected obviously, but no changes to sensitivity or output power (or any other parameter)
View ArticleForum Post: RE: NV circular history logging on CC2540
You can view flash memory directly with IAR debugger by poking the appropriate values into the memory mapping register(s). Its been a while, so I don't remember exactly which register.
View ArticleForum Post: RE: Wilink8 (Com8 module) for AM335x
Hi Adnan,Just checking in if there are news on these modules. Are datasheets and code-stacks released in full by now?bestDavid
View ArticleForum Post: RE: Issues about enabling security (SE Profile)
Hi,you must download the test certificates in the NV area on MSP430 based platform. Please refer to section 2 in Smart Energy Sample Application User's guide to see how to generate the test certificate...
View ArticleForum Post: Loading Packet Sniffer firmware onto Chronos USB dongle
When I first started working with the Chronos kit several months ago, I put the packet sniffer firmware on the CC1111 USB dongle fairly easily; I attached my CC debugger to the test points on the...
View ArticleForum Post: RE: Rerouting not working properly
Hello Oded, I will run the tests and get the results back to you. Can you please contact me offline regarding this issue? There is some information which I can't make public.Regards,Derek
View Article