Forum Post: RE: CC3000 module: Front-end-module
Nagata,The FEM on the CC3000 module includes a PA and a TX/RX switch. The output of the FEM is single ended 50 Ohm.Gil
View ArticleClik here to view.
Forum Post: CC8530 protocol slave can select between 8 audio channel, but how...
I am designing a multi room audio system based on CC8530 purepath chipsets and I am confused about audio channel selection. According to configurator software, the protocol slave can select between 8...
View ArticleForum Post: RE: Protocol/chip selection
Hi,That is correct, these modules can plug into ANT development interface boards (with the molex connector mounted) and not directly into MSP430 Experimenter boards.Best regards,Harrison
View ArticleForum Post: CC1110 Peripheral Simulation Plug-in (PSP)
I am using IAR's 8051 IDE Workbench and want to simulate the TI CC1110 chip using the CSpy simulator to determine the timing for sections in my code but I didn't see any PSP modules in the install...
View ArticleForum Post: CC2543 dropping packets?
I have two 2543 SmartRF Eval kits running. Board 1 starts by transmitting packets. Board 2 starts by waiting for a received packet. Every 10msec board 1 transmits a new packet. Each new packet has...
View ArticleForum Post: RE: LF RFID Reader
Hey Hussain,I also wanted to point you to our MRD2EVM. You can use this EVM to read the LF tags. Thanks,JD
View ArticleForum Post: RE: How does a router which is lost, get back to the network with...
Hi,YiKai,Considering these following two cases:Case A: There is a coordinator and a router working in a zigbee network.For some reason ,the coordinator is powered off. Then the router will...
View ArticleForum Post: RE: WL1271 : ANT & bluetooth
Hi Adnan,I am also interested in getting an ANT+ demo running on the AM335x EVM w/ the wl1271. I haven't seen the requisite driver sources available in the AM335 PSP. Are they publicly available? Can...
View ArticleForum Post: RE: PROBLEM: LINKING WITH IAR
Hi,I am using Windows 7 64bit with IAR 7.60.I've just downloaded the 7.60 version of IAR with a 30-day evaluation license. When I rebuild the project I get the error:Fatal Error[e72]: Segment...
View ArticleForum Post: RE: cc112x_easy_link software doubt
Also pls some one help me what the below condition checks#define TRXEM_SPI_WAIT_DONE() st( while(!(UCB0IFG & UCRXIFG)); )I'm not that much familiar with MSP430 programming/architecture. So...
View ArticleForum Post: Notification per ConnHandle
Hi,My simplePeripheral allows for multiple concurrent Central connection.Now when when one of the Centrals (IOS devices) writes a "Command" characteristic, the application processes the received Value...
View ArticleForum Post: RE: Getting started with CCS and CC3000
Hi. Any ideas on where I might be going wrong? I'm still stuck on this. Thanks!
View ArticleForum Post: CC3000 and stellaris lm4f120
Hey,I am trying to learn how to use wifi with a CC3000 and a stellarisware.I didn't get the wifi evaluation kit of stellaris ware.Can someone tell me how to can connect the launchpad with CC3000?Thank you
View ArticleForum Post: cc antenna dev kit drill sizes
HiHello i have r question about antenna dev kit gerbers.Antenna traces on both sides are connected with series vias all the way. The drill sizes are very small. (~0.24) My pcb provider for test pbs...
View ArticleForum Post: RE: do zstack need an OS to run?
thank you YiKai for your interest.is there any example code or application based on osal only, because all examples I found are using freeRTOS.regards
View ArticleForum Post: Failed to erase flash CC85xx
I can't program any of my four boards. It fail on erase flash. CC debugger with latest firmware has green LED and correctly detect device CC8521 and CC8531 in my case. I red some previous articles...
View ArticleForum Post: RE: Notification per ConnHandle
Hi Oliver,It is not possible for a peripheral device to be connected to multiple central devices so I do not really understand your question. Anyway, looking at the client/server perspective...
View ArticleForum Post: RE: cc112x_easy_link software doubt
Jinesh, This line while(TRXEM_PORT_IN & TRXEM_SPI_MISO_PIN);Make the MCU wait for the CC1120 to indicate that it is "ready" to accept commands. The next one st( while(!(UCB0IFG & UCRXIFG));...
View ArticleForum Post: RE: BLE Chip with both USB and I2C support
Why does I2C software bit banging not work?I have a project with quite similar demands (USB and 2 x I2C) and it works quite well with the CC2540. The I2C is quite easy to emulate,
View Article