Forum Post: RE: Command Line Interface cli for WL1271
Hi Victor,your link was very helpfull to me. Thank you. Do you think i could substitute mac80211 with MLP on my board ?
View ArticleForum Post: RE: Autonomous Control of CC8531
Kjetil,Thanks for your help! I have been told that our HW design has changed and we need an MCU.I may be posting a seperate question shortly! : )Regards!!
View ArticleForum Post: RE: CC3000 SPI Clock Polarity and Phase
the diagram on wikipedia makes it very clear.
View ArticleForum Post: RE: flash memory access cc2530
Hello againI have tried with zstack 2.5.1a and the problem persist. I can read but i can not write with the boot of the sbl.Another problem is to define HAL_PA_LNA in the boot becouseError[e46]:...
View ArticleForum Post: Host Controlled and setting up volume controls for the the slave
I have been assigned the duty of setting up a prototype for a drive-thru/headset scenario.I am working with the PPW Configurator 1.4.1.38034. My question deals with the volume controls. We will be...
View ArticleForum Post: RE: Does CC8520 use Spread Spectrum?
Hi Kjetil,Ok, now is clear for me. Thank you.Best regardsRF_PTS
View ArticleForum Post: RE: CC3000 matching elements dimensioning
And, I'm confused as to why we need the 10pF C2 close to the module on the CC3000EM schematic. The Johanson matching circuit only shows a single C/L combination to achieve 50 ohms. Assuming the CC300...
View ArticleForum Post: RE: CC3000 not initializing properly
Hi,I have the same problem than you with the latest CC3000 version wich include all TCP/IP tool.I have exactly the same logic result than we can see in this thread. Except than with the evaluation...
View ArticleForum Post: Update the Advertising Interval while Advertising
Hi everyone,I want to update (change) the advertising interval from one value to another while the CC2541 is advertising.The way I'm currently doing it is //Set the advertising interval to the new...
View ArticleForum Post: RE: CC2541 DC Current Consumption (Layout Issue?)
The problem is solved: It was a layout mistake on our side. Do not connect DCOUPL to Vcc...
View ArticleForum Post: RE: using nvram on the CC2540
Richard,You could use read/writh with Osal svn. There is 2KB in NVRAM that you could use for your application.This is link that has more information for you to do this...
View ArticleForum Post: RE: TCP Connection lost after working for some time in CC3000
Please look into this issue
View ArticleForum Post: issue reading or writing during multiple concurrent connections...
During a BLE master device scan, 3 peripheral devices are discovered. The BLE master is the GATT server also. A connection is made successfully to each device, different handle for each. T However...
View ArticleForum Post: RE: Range Distance with CC112x - Can you achieve further than 25km ?
Hi Richard!We have tested the CC1125 With evaluation board development kit but We have a very short range of distance only 0,5km!!! @ 868Mhz and 300bps (2% error rate 100 packets).The 2 evaluation Kits...
View ArticleForum Post: RE: Wifi module hangs.
from the table above it really looks like J4-2 and J4-6 pins are the two pins for driver and firmware logs.BUT, from my experience, I am working with J4-1 and J4-3 pins for log captures.Maybe it...
View ArticleForum Post: RE: cc2520 gpio register value 0x46
Hello.I too am looking for said documentation about the undocumented register values. Where can I find the preliminary document?Also, I'm curious why would this important information be removed from...
View ArticleForum Post: PAN1323ETU module start up
Hello all, I have a PAN1323ETU module that I am trying to get working. The board is powered at 3.3V, with all logic to the module at the same voltage. (The board has level shifters for the CC256x.) I...
View ArticleForum Post: RE: Firmware debugger ili file for 6.1.3.50.58
Hi,Where did you download/get the Driver / FW from? What is the driver version you are using? Regards,Barak
View ArticleForum Post: RE: Change Advertising interval
Hi, There is possible way to try: set your own period event and change the period time in each time.In the period function, set adverting enable.Hope it helps.Jack
View Article