Forum Post: RE: CC-6LowPAN Edge Router OMAP-L138 Booting Error
I have the same problem. Can some one help?
View ArticleForum Post: RE: sniffer shows packets but the actual data sent not seen in...
Hello Lakshman,Does RFstudio work with all sample applications for cc2530?For example sa SerialApp application, in this if there no code to send packets on JTAG/cc-Debugger for RFStudio how would...
View ArticleForum Post: RE: How TO CHOOSE ANTENNA FOR CC2541
ok fine . My doubt is , only after buying THE CC2541 MINI DK . i can program this chip(CC251) i am right?
View ArticleForum Post: RE: CC1175 in OOK mode code examples
The CC1175 is a transmitter only. You would modify the sample code, by eliminating the receiving section. Thanks,
View ArticleForum Post: WL1271 CONTAIN IN-BUILD ANTENNA or NOT?
hi all i have been choosen the WL1271 this is module right. whether this module have in -build antenna or externally i have to build please clarify this. thanks.
View ArticleForum Post: Power sensor for CC2530
Hi guys,i am using the ZigBee developement kit CC2530ZDK for a building automation application. In fact,i need to measure the ambiant temperature, humidity and power-consumption of the devices in each...
View ArticleForum Post: RE: CC254x BLE SoC Interoperability Qualification
Hi Anas,When we qualify our stack, a test house uses a Bluetooth Tester (example Rohde & Schwarz) to run through the test cases and verify that we follow the core specification.We do attend to...
View ArticleForum Post: RE: RE: Uniflash 2.1 not loading program on CC2538
Hi Greenja,[quote user="greenja"]can we safely say that CCS will support it?[/quote]Now you're thinking outside the box :) That is a good assumption.Best Regards
View ArticleForum Post: RE: Maximum number of Slave connection for CC2540 Bluetooth Low...
http://e2e.ti.com/support/low_power_rf/f/538/t/202802.aspx
View ArticleForum Post: RE: IPv6 over BLE status?
Hi Rene,I remember some draft a while back but that was not from Bluetooth SIG. I believe it was a 6lowpan working group (http://tools.ietf.org/html/draft-ietf-6lowpan-btle-09). Or do you have another...
View ArticleForum Post: RE: USB CDC + UART at the same time
Is the problem that they are both using the same interrupt and you get corrupt data?You will have to specify exactly where and what you are having difficulties with.Thanks,
View ArticleForum Post: RE: CC3000:Issue with TCP
Hi,I believe we have been able to reproduce the problem. The issue is related to a race condition where 2 back to back command (recv) and data (send) reach the CC3000 device. We are currently working...
View ArticleForum Post: Zstack on sub-1GHZ
Hi, As I know ZigBee PRO operates in ISM radio bands 868/915 Mhz and 2.4 GHz.Due to the range problems 2.4GHz does not satisfy my needs.I wonder, whether TI plans to release ZStack for sub-1GHZ or...
View ArticleForum Post: Zstack on sub-1GHZ
Hi, As I know ZigBee PRO operates in ISM radio bands 868/915 Mhz and 2.4 GHz.Due to the range problems 2.4GHz does not satisfy my needs.I wonder, whether TI plans to release ZStack for sub-1GHZ or...
View ArticleForum Post: RE: DOES FIRMWARE NEED FOR CC2541 BLUETOOTH CHIP
ok . i had query. i see part no WL1273-TIW5 Contain in build antenna or externally i have to built?
View ArticleForum Post: RE: CC3000 not initializing properly
Hi,my investigation show that :1) If CC3000 dosen't perform falling edge on its IRQ you will never be able to load a new firmware or do a normal start2) My XCC3000 are.....empty. No bootloader and no...
View ArticleForum Post: RE: CC3000 - understanding the power pins
Hi MaciejThanks for the response. I've been through the datasheet and wiki - hence my question. In my opinion, it's not clear from either.The diagram implies it is for IO levelling but this is not...
View ArticleForum Post: Using Labview to read data from cc2540DK mini
Hello all,I am trying to read the accelerometer and button data from the cc2540dk mini keyfob and display this through Labview.Has anyone been successful with this? if so what's the best way to go...
View ArticleForum Post: RE: CC2540 Mini kit - making the keyfob discoverable
Dear Nick,I am trying to update the FW on the keyfob rev 1.1.1. with the CC2540MiniDkDemoSlave.hex...but when I try to downoad the hex into the CC2540 with the CC Debugger I have always this...
View Article