Forum Post: Need to send multiple messages from Host to get first message at...
Hello,Many times it is observed that if we just want to send a message from host, it does not go thru even of 100 byte size. Probably it sits at CC3000 and wait for another message and then send it all...
View ArticleForum Post: cc2540 usb dongle is not seen by CC-debugger nor by SmartRF!
I want to flash the CC2540 USB dongle to use it as a gateway between the Sensortag devices and my laptop.However, the device cannot be detected by the CC-debugger nor by SmartRF or SmarRF programmer...
View ArticleForum Post: RE: Ztool : How to launch the network discovery by ZTOOL
Nop it's not working, i have the same error :<TX>05:24:48.14 COM3 ZDO_MGMT_PERMIT_JOIN_REQUEST (0x2536) DstAddr: 0x0000 Duration: 0xFF TCSignificance: 0x00<RX>05:24:48.16 COM3...
View ArticleForum Post: RE: SPI connection to CC2541 running HostTestRelease
Is there anybody at TI who tested BLE 1.3 in SPI mode and can release as sample the function that handles the DRDY asserted from the slave and a sample 'reset chipcon' function?I am surprised that the...
View ArticleForum Post: RE: What firmware(SOFTWARE PACKAGE) been used for COMBO MODULE?
Hi Janaki,You'll need a host platform in order to run any kind of software. Please checkout the Sitara page for an evaluation kit and software download.
View ArticleForum Post: RE: BR-LE-4.0-S3A Changing UART speed over BLE GATT
Ah, again, super helpful! I think that was my exact problem. I reset before disconnection... Silly me.
View ArticleForum Post: CC1111EMK868-915 Sniffer Whitening
I am trying to use the CC1111EMK868-915 and TI sniffer software to watch a proprietary 915Mhz protocol. I was trying to use the SmartRF Studio platform with a SmartRF04EB and CC1101EM but then...
View ArticleForum Post: TRF7970A, min data clock, 1MHz
Hi allMy customer is using the TRF7970A with 1MHz fD_CLK.Looking at the Datasheet http://www.ti.com/lit/gpn/trf7970a page 12 we specify for fD_CLKmax 2MHz 8MHz 10MHz range, this is somewhat...
View ArticleForum Post: RE: CC2530DK IR generation
Do you have the target board schematic diagram? I can send a? Black and white remote control principle diagram and the principle of remote control chart is the same? Did I want to ask next use remote...
View ArticleForum Post: RE: ZigBEE for AM335x development platform
Assuming you can develop with C or some other laguages on Linux, you should have no difficulty to play with CC2530ZNP firmware via UART interface.Unless you want to build a whole ZCL support framework,...
View ArticleForum Post: RE: CC2540 Op amp as a load cell signal amplifier
Hi,Thanks for fast reply. It steered me in the right direction. I find this document very useful: http://www.ti.com/lit/an/sloa034/sloa034.pdf .Regards,Igor
View ArticleForum Post: RE: Monopole PCB antenna - ground plane effect ?
Hi Jan,Not a dumb question at all! Yes, you can place the antenna as you have done in your layout.You should really try to get access to a lab with a network analyzer to adjust the antenna length and...
View ArticleForum Post: RE: CC2540
Hello John,And remember to connect ground as well and you should be good to go.BR. Eirik
View ArticleForum Post: RE: Question about timing on cc2530~
The timing with Onboard_wait() still incorrect for me. Any idea why ?! Thanks
View ArticleForum Post: Code formatting
Hi,Maybe my question is not related to this section and trivial but ill try.Why some of the functions are typed with capital letter and some not. E.g. accelRead and Accel_SetParameter. The functions...
View ArticleForum Post: RE: Multiple central and single peripheral
Hi greenja,I kept 3 second "osal_start_timerEx" just before connection request as follows osal_start_timerEx( simpleBLETaskId, LINK_ESHTABLISH_TOUT_EVT, MAXIMUM_LINK_EST_TIME );Status =...
View ArticleForum Post: Send RF data Based on Time Interval
Hello,We have purchased TI-KIT-MSP-EXPCC430RF4.Our application is based on OpenTag RTOS.Now we want to send RF data based on Time interval i.e. every 30 seconds we want to send data over RF.How can we...
View ArticleForum Post: RE: The Server does not receive any data
Reviewing the CC3000 Host Driver Porting Guide with last version of "CC3000BasicWiFiApplication\Basic WiFi App MSP430 Source\Source\CC3000 Spi"Our porting only change:1)#define ASSERT_CS()...
View ArticleForum Post: RE: CC8520 RF Issues
Hi Marice,Sounds very odd. Have you tried more than one board/chip?I added you as a friend.-Per
View ArticleForum Post: RE: Wireless HART Stack
Hi,I am looking for WirelessHART stack 3rd party stack provider for MSP430 or similar platform.This is product design, so paid stacks are also ok. If any one can help us on this front, please respond,...
View Article
