Clik here to view.
Forum Post: Request Identifying the CC2541F256_Chip_Set problem.
Request Identifying the CC2541F256_Chip_Set problem.Within the interrupt occurs in PORT1[2], the ISR routine P1IFG_2=1, and P1IFG_3=1 Register is set at the same time is a problem occurred.PORT-1...
View ArticleForum Post: RE: RS232 data to an AP using CC3000
Hi,I'm facing a similar problem - I'd like to use the cc3000 for sending snapshots taken by an RS232 camera. As I've seen in the MSP-EXP430FR5739 data sheet it has one serial port which I believe...
View ArticleForum Post: RE: Electronic Shelf Label
Contact the company that made the kit:http://www.pervasivedisplays.com/contact/home
View ArticleForum Post: RE: which tool is mostly suitable for Zigbee based application
Your question is too general. Do you want to read chapter 2 on the book Zigbee Wireless Networking.
View ArticleForum Post: RE: CC2540 Connection parameters
Hello Artem,There was a similar post to yours where the connection interval of 100ms was a problem. Take a look at how they finally resovled the...
View ArticleClik here to view.
Forum Post: RE: Confusion on appropriate firmware version for Wl127x application
Victor,You're right - I misspelled the model number. It is WG7310.We are trying to pass a wifi regulatory test. Sorry, if what follows is a little confused - I'm not directly coordinating the...
View ArticleForum Post: RE: wlan not working on Jelly Bean on Blaze Board
Hi Prakesh,Please use wpa_cli to check the operational status of the WLAN0 interface.some examples can be found here :...
View ArticleForum Post: RE: Very low range in desert terrain
First a question a bit on the side: I would assume that when tracking wildlife range is important. Why are you not using a sub-1GHz device like CC1120 that has higher output power and better...
View ArticleForum Post: RE: LPM mode
It is very unclear from the post which chip you try to use in LPM?
View ArticleForum Post: RE: eWOR / SniffMode timing problems
Thank you, this was the Problem.After enabling automatic calibration the t_Event0 duration changed to my expected values.I have one more question:Is there an easy way to figure out the Rx-Time value...
View ArticleForum Post: RE: Multiple central and single peripheral
Hello. This command does work when trying to connect. Make sure that you are using the correct connection handle. What status is the command returning?-Tim
View ArticleForum Post: RE: Smart RF Studio has no Sniffer export like the documentation...
Although I was able to get some communication with the packet sniffer from SmartRF Studio 7, I couldn't pick up anything using our code to Tx while using the same SmartRF register settings.This could...
View ArticleForum Post: RE: CC8521/CC8531 USB dongle as MASTER ? CC8520 as SLAVE?
Hi Jack, Yes, the CC8521/CC8531 can be designed as a USB dongle and master. The dongle will be compatible with most OS, see attached comp-ability matrix. Have a look at the reference design...
View ArticleForum Post: RE: wl1283 in custom board
Hello,In order to get more information about 1283 and specially our GPS drivers, you will need to sign on NDA.You may use omappedia website to figure out the driver changes that are needed for Android...
View ArticleForum Post: RE: Changing device attached name on iOS device
O.K.,I don't know how you can solve that problem if it is truly an iOS restriction.What you may try doing is have the iOS call another function to change the device name. If BTool can make the change,...
View ArticleForum Post: RE: CC8520 Clarification
OK! thnakyou for the information!These days i had a little more time and i studyed every tehnical data i could find about this cip! Initialy i wanted to use only the wireless transmision for my Digital...
View ArticleForum Post: RE: How to use serial port over cc2540 USB EMK
HiIf i senf 0,0,0,0 then 1,1,1,1 then 2,2,2,2 ........ 255,255,255,255 - means each byte 4 time i got the...
View ArticleForum Post: RE: Wearable BLE devices, 3 slave limitation
Hello Uri,If your smartphone or device is iOS and if the BLE devices will be known then a possible solution would be to name them sequentially.In your BLEDiscoveredPeripheral you would record all the...
View ArticleForum Post: RE: wl1283
Hi,wl128x-fw* firmware is for WLAN only.Bluetooth needs BTS files as firmware.Regards,Abhijit
View ArticleForum Post: RE: CC2540 MCU power consumption without BLE stack
Hello Keni,Most of the answers you are looking for can be found in this very thorough Application note.Measuring Bluetooth® Low Energy Power Consumption Application Note AN092 swra347a.pdf should...
View Article