Forum Post: RE: Why the connection from IOS to my keyfob takes such a long...
Yes, with the default setting, it use the master's connection parameter,but not slaves. But the current is large, it is about 1mA if connected. So I want to decrease the current of keyfob, so I want to...
View ArticleForum Post: SPI speed degrades CC1120 RF performance
Hi,I am developping a product using 5002eZDSP kits and CC1120 EVM boards. I am running the CC1120 with the values from RF studio for 200kbps @ 868mhz 4GFSK. I get good range when I operate the SPI bus...
View ArticleForum Post: RE: CC2510 wrong UART timing after power ON
There is a sample software package for the CC1110/C2510 http://www.ti.com/litv/zip/swrc117 that has some UART examples. Thie following code is taken from the example and this is how they initialize...
View ArticleForum Post: RE: Reducing power consumption in TX mode for CC1120
Ok, I'm using the TrxEB, which has dedicated pins to measure power consumption on the MCU, I/O and radio seperately. Yeah i'm using a series coupled resistor and measuring with an oscilloscope. In my...
View ArticleForum Post: RE: RF transceiver with matched filter
Thank you very much for the answer!That's what I'm looking for.Regards, Andre
View ArticleForum Post: CC3000 interface with TMS320C5535
Hello,5535's Spi works such that you can only add 0, 1, .. 4 bits delay between CS assertion and first CLK edge. However, with CC3000, one has to assert CS and wait until IRQ goes low before starting...
View ArticleForum Post: RE: SSL implementation on DSP for Simple link
Anyone who could have worked with OpenSSL, yaSSL?www.openssl.org/www.yassl.com/Thanks for feedback,Jean
View ArticleForum Post: RE: Android and Bluetooth Smart - It works on the Samsung S3 phone
Google just announced official BLE API coming in API 18 later in 2013!https://plus.google.com/116110604589325140832/posts/bmqALtLu5oj
View ArticleForum Post: RE: HalUARTWrite()
Do you use your own CC2530 pcb or CC2530em+smartrf05? I suspect that there is HW problem on UART. Do you want to check HW first?
View ArticleForum Post: Which of the several Bluetooth LE modules should I consider to...
Hello to all,My request is for some comments and suggestions about “which of the Bluetooth modules” and “the assocaited development system” should I be using to develop the Bluetooth communications...
View ArticleForum Post: RE: Question about MSP430 and Bluetooth
Hi Miguel, I read on the forum, that we can’t develop an Bluetooth application for IOS without MFI.I found a blog that tell the CC2541DK-MINI succeed to pass this issue....
View ArticleForum Post: RE: Microstrip width sanity check
It is the distance from the routing layer to the first ground layer that is important. For the CC1101 standalone ref design this distance is 0.8mm. If you look at the CC1101-CC1190 ref design which...
View ArticleForum Post: RE: CC2540/41 BLE compatibility
Hi Chris,The recommendation is to ground pins 1-4 if not using the USB.Regards,BK
View ArticleForum Post: RE: SensorTag on iOS times out after 15-30 minutes
I had been working with an iPhone 4S, but after switching to an iPhone 5, the disconnections stopped. I was able to leave the SensorTag connected to the iPhone overnight without any errors. This leads...
View ArticleForum Post: Couple of basic questions about using host-controlled CC85xx
Hi,Sorry for basic questions, I'm new to in-depth aspects of PurePath:1) We are planning to use CC8520 controlled by CC430 MCU via EHIF. We want to use pre-defined configuration provided by PP...
View ArticleForum Post: RE: SCO Initiialization Timeout
Hi Radar,Even if the HCI UART failed to initialize, we need to see the logs “Bluetooth: HCI UART driver ver x.x” as it is at the start of the function.From the logs provided it is hard to find out if...
View ArticleForum Post: RE: Question about MSP430 and Bluetooth
Hello Eyal, The CC2564 provides BLE too. Therefore, you can connect to iOS devices without the authentication chip. An examples is located here:...
View ArticleForum Post: RE: CC 2591 Wake On Radio
Hi, I was wondering if this questions was answered, as I am also interested in knowing if CC2591+ CC2500 support the wake on radio function. Regards, Ben.
View ArticleForum Post: RE: Meaning of atAuthenticationStatus Codes in Bluetopia Stack
Hello Florian,Our partner SSO will clarify this parameter.Regards,Miguel
View ArticleForum Post: RE: Running the SSPDemo on the EZ430-RF-256X
Hi Chuck, The steps are shown in the links below. Regarding the terminal, did you check on the COM port?- EZ430-RF256x HW Setup:...
View Article