Forum Post: RE: TRF7970A Low Power gives higher received signal strength (RSSI)?
Josh,I've got a PSA1301T 1.3GHz Spectrum Analyzer. Its a handheld unit, but I dont know if it is any good.It's got a max input power of +20dBm and ±15VDC. I dont have any attenuators, but if I run the...
View ArticleForum Post: MSP430F6633 and CC3000 Wi-Fi
Hallo forum users,I am currently designing a handheld measuring device using the MSP430F6633 microcontroller and I need an integrated web server application in the device in order to see the...
View ArticleForum Post: RE: binding question
Dears,If you want to send message from coordinator to end device using binding, you need to make end device allow binding and coordinator to send out binding request. Once coordinator received...
View ArticleForum Post: RE: Sensortag not working...
Hi Ramanand,All SensorTags (including all sensors) are tested in production so they should be functional. I've experienced the same issue a few times, and when I had these problems the issues were...
View ArticleForum Post: RE: ISM Band Sub-GHz RF Transceiver for Smart Lighting System
Juan, The CC2530 uses 8051 MCU, which CCS does not support. The only option is IAR.Regards,/TA
View ArticleForum Post: RE: sensor network
Thank you for your response Arvydas!Here are a couple of questions I was hoping you could help with:1) Do the sensors connect directly to the CC2541? a) If so, I saw the CC2541 has 23 I/O pins, are...
View ArticleForum Post: RE: Conflict between CC2530 User's Guide and hal_digio ISRs?
hi,if i d'ont touch the registers IP0 and IP1 of configuration priority cc2530 use the pollign sequence in the data sheet !!?? How to configure P1 INT more priority than T1 INT i d'ont understand how...
View ArticleForum Post: RE: deplicate UUID found under advertising mode
Is it means this is normal operation? and it is required handle in Apps (don't show deplicated UUID)?Edwin
View ArticleForum Post: wl1271 calibration
Good afternoon,I'm Alberto Garau and I'm an engineer involved in a project where we use the wl1271.We have the device running in SPI and we are observing a strange scenario. When the AP is placed 10...
View ArticleForum Post: Unknown chip?
Hello.Today saw Bluetooth module with CC2562F256 chip. Could not find any info about it at all. Can anyone help?
View ArticleForum Post: RE: connectivity cc2550-cc2590-50 ohm power amplifier
Dear Richard,I just read the CC2520 datasheet, and noted that the its differential output has high impedance, so the matching network should be different that in the case of the CC2550. This example of...
View ArticleForum Post: RE: problem connecting Zigbee Z-Stack EP to coordinator network
Hi,I've been searching on the web to try to find out what is this "supposed" TI stack issue that Digi is talking about, but I can't find anything.Do you know what is this stack issue that they could be...
View ArticleForum Post: RE: link token & join token, automatic change?
By the way, is there anyway to assign the link or join token at the runtime, before SMPL_Init (), just like assigning address using the SMPL_Ioctl?
View ArticleForum Post: Unique Internal Identifier in CC2540
Is there a unique serial number that can be accessed from within the CC2540? I'm looking to uniquely identify each peripheral all running the same code. Is the UUID guaranteed to stay the same...
View ArticleForum Post: RE: CC2564 available for 10 years?
Hi Amy, Per TI Obsolescence Policy: TI standard policy on the lifetime of devices, the following paragraph applies: We are not able to forecast future market demand for a TI device and accordingly,...
View ArticleForum Post: CC2540 Mini Kit Files & Attribute Table Question
I'm a bit confused over the HexFile naming conventions in the BLE-CC254x.1.2.1/Accessories/HexFiles folder.This folder contians hex files for both the keyfob and the USBdongle, right?I presume for the...
View ArticleForum Post: RE: Basic data exchange between phone and sensor
Hi Nick,Thanks for your answer!So, what I need to do is:1. First time I need to pair the devices to exchange Identity Resolving Key (IRK).2. Close the connection2. Now, doing the Advertising and...
View ArticleForum Post: RE: CC1110 Noise floor/ 250Kbaud,GFSK
Yes I figured out how to change the AGCCTRL value. Currently the value I have set is 0x07. Changing it to C7 is showing a degraded operation.Thanks for the explanation. I really appreciate. Currently...
View ArticleForum Post: How can I change CC254x SBP_PERIODIC_EVT_PERIOD using BTool?
Hi. I'm using CC2541 and I want to change the SBP_PERIODIC_EVT_PERIOD value using BTool.I made the GATT table for this, and success to write properly, but the period of running...
View Article