Forum Post: Bluetooth antenna orientation.
Hi, I am a newbie in RF. I am using a Panasonic PAN1323ETU bluetooth module. Does the antenna orientation effect the range of bluetooth? Should there be 2 different antenna orientations for...
View ArticleForum Post: RE: CC1101 Receiving sensitivity and Layout
I see the following possibilities or a mix:-> The recommended register settings have not been used-> The hardware does not follow the reference design-> The sensitivity measurement method give...
View ArticleForum Post: Getting Started with PAN1326 and A2DP
Hello, I'm looking to use the A2DP protocol for a Bluetooth application for a PAN1326 chip. I have C and C++ programming experience but have never programmed for Bluetooth before. What do I need to...
View ArticleForum Post: RE: How to handle GPIO pin of CC85XX?
Hi RF_PTS,You set the initial stateof the GIO with the line:<initial_setting>0</initial_setting>Here you set 0 or 1 based on what you want.RegardsKristoffer
View ArticleForum Post: RE: CC11xx TCXO frequency boundaries
It is not valid for CC1120/21. The upper limit for these devices is 33.6 MHz.
View ArticleForum Post: RE: CC2543 Radio reset problem (RESET_N seems to only affect CPU)
[quote user="David Paulsen"]Thanks so much for your suggestions! I think I found the problem. The FPGA has a PLL that generates its clock frequency, and it seems to have a startup problem. When it...
View ArticleForum Post: RE: Sensitivity different od receiving packet via RFStdio from...
If you use Sniff mode make sure the preamble length matches the wake up interval. Also, make sure the TX interval is long enough if you send more than one packet (receiver needs time to receive current...
View ArticleForum Post: RE: PHY_Reset endless loop
It's works now ! I've progressively replaced files in my project from initial BLE folder to my new arborescence.Thanks to all for your help ! Antoine.
View ArticleForum Post: CC256x HCI_VS_Set_LE_Test_Mode_Parameters Fails
Tech Support,Customer has waded through the various updated instructions on BLE Transmitter and Receiver tests. I’m finding that HCI_VS_Set_LE_Test_Mode_Parameters is failing with a 0x0c HCI status –...
View ArticleForum Post: RE: CC2531 USB dongle and SimpliciTI : BSP / sample code.
Hello,I do not have any idea about your issue, I am sorry about that, I have disturbed you because of my point, firstly thank you for your consideration.I am new in iar and CC applications, and also...
View ArticleForum Post: RE: Murata's CC3000 TB current spike issue
Well if this is a matter of days, then I'll wait. I will contact Murata to get info on startup current requirements. Thank you.Regards,Jean
View ArticleForum Post: RE: wl1271 port on TI 8148
Hi , I have my custom board that is close to beaglebone rev A3 , I'm trying to get WLAN working on this system. The host processor talks to the WL1271 chip over an SDIO interface , i I've...
View ArticleForum Post: ZNP Application on CC2530 gets stuck
Hello,We have some devices comprised of a MSP430F5528 (ZAP) and a CC2530 running the 2.5.1 ZNP application. The interface between the two is SPI. We've been noticing that, after an undefined amount of...
View ArticleForum Post: RE: [BLE] Do I read RSSI value in ADV_SCAN_REQ packet???
Hi,As far as I know you can only get the RSSI value within the actual device you obtain the value from... so to answer your question: No.Best Regards
View ArticleForum Post: RE: IP lost (v1.10)
Hi I think i have found the reason for the lost(not renewed) IP.I my application code I added some additional delay (100 ms) in between my module communication.I guess i might have kept it to busy...
View ArticleForum Post: DHCP not working with cisco WAG160Nv2
Hi I am testing a module with the new smart config and iOS app. I have tested with a netgear and a tp-link router and that works perfectly.But DHCP doesn't work with Cisco WAG160Nv2 when this AP is in...
View ArticleForum Post: RE: Creating CCS Project using SimpliciTI
Niket, I opened up your project, you have an extra main.c in the project. Remove that one and not Link_To.c.It compiles on my end now./TA
View Article