Forum Post: RE: WL12xx WiFi+BT on AM335x - BT Initialization fails
[quote user="Sundeep Mandava"]Hi,First you need to have a UIM executable. For this you need to create a Makefile to compile UIM in “uim-sysfs” folder.Once you have the uim-sysfs executable.You need to...
View ArticleForum Post: RE: WL12xx is not getting initialized....
Hi Abhijit, below is my platform inilization #define AM335XEVM_BB_WLAN_IRQ_GPIO GPIO_TO_PIN(2, 5)#define AM335xEVM_BB_WLAN_EN_GPIO GPIO_TO_PIN(2, 2)struct wl12xx_platform_data...
View ArticleForum Post: RE: how to overcome IAR embedded workbench code size limitation...
Hi VigneshI would strongly recommend you to buy a full version of the IAR Embedded Workbench if your project size is above the 4k size limitation that the Kickstart version gives you.To evaluate the...
View ArticleForum Post: RE: basic wifi application msp430 cc3000
thanks a lot, for your answear, the wifi application works with ccs 5.2 , i'd have another question now:after doing smart config the cc300 is authenticated but not connected , is it right?should we...
View ArticleForum Post: RE: Query in my Design
This looks correct. AVDD6 is not connected, but you have probably seen that already./F
View ArticleForum Post: RE: Iran: is 868Mhz allowed there?
Our sub 1GHz RF chips are made to cover the most used ISM bands and the most interesting geographical regions. It is up to the customer to make a product that comply with the regulations within the...
View ArticleForum Post: RE: selection of advertising channels CC2540
Hi,I would suggest you checking the forum by using search box for a more efficient forum. Your answer is in the following...
View ArticleForum Post: RE: How to reduce the Consumption stream after disconnect
Hi Nick: I set GAPROLE_ADVERT_OFF_TIME to 0 and set GAPROLE_ADVERT_ENABLED FALSE or TRUE every 12s after disconnect. As my understand, the 2540 will braodcast 12s,then stop 12s,then broadcast...
View ArticleForum Post: RE: a question about NWM_GET_STATUS
I look at the ACH_USED field first, which tells you which channels are in use. I'm not sure if the data in the DEVICE_ID field is valid if the ACH_USED bit is 0.
View ArticleForum Post: info about smart config cc3000
hello,i'd have a simple questino about cc3000..after doing smart config the cc3000 is authenticated but not connected , is it right?should we set a static IP to let the cc3000 acquire its own ip...
View ArticleForum Post: RE: CC1120 & PLL reference
I wasn't thinking about the app note too much, I thought about the last posts in the thread I was linking to. First, without knowing the deviation in your system it's not possible to calculate. You can...
View ArticleForum Post: RE: Murata / Johanson IPC for 434 MHz?
Hi,There are plans of a new version of the CC1120 IPC at 434 MHz. The exact date for samples / release is still too early but a rough indication will be towards Q4 this year.Regards, Richard.
View ArticleForum Post: Universal Boot Loader for 128kb CC2540?
Hi all,I would like to find out if it is possible to use the UBL with a 128kb CC2540 SoC. I have tried out the "CC2540-Dk-128kb" configuration of the UBL project but i was unable to load the image to...
View ArticleForum Post: RE: CC1110 tuning
Since you want to tune your design I assume you see some issues with the existing one. If you could tell us more about why you want to tune your design it will be easier to point you in the correct...
View ArticleForum Post: RE: Tx SFD - Rx SFD delay
The SFD delay should be fairly constant after the issue of the STXON strobe using the CSP, the delay is a few microseconds .From User's Guide:Transmission of preamble begins 192 μs after the STXON or...
View ArticleForum Post: RE: CC3000MOD Antenna alternative to ACX AT8010-E2R9HAA?
Hi Zach and Tony,The chip atenna TI recommends for this module is the AT8010. If you use this same antenna you can bypass FCC recertification by the "Modular" grant.Specifically, the TI CC3000MOD is a...
View ArticleForum Post: RE: New BLE 1.3 version fails build in linking stage
Yes, a colleague had access to 8.11 that seems to work for me now as well.I wish toolchain dependancy was mentioned in the release notes or on the download page.
View ArticleForum Post: RE: RF korean certification for product including TiWi5
Hi,Currently it is not possible to control the output power of the CW (tone signal).The typical maximum output power is:+20.0dBm at 11Mbps, (11b)+15.0dBm at 54Mbps, (11g)+14.5dBm at 65Mbps,...
View ArticleForum Post: RE: WL1271 WLAN+BT, what about ZigBee
Hi,as you you wrote it is recommended to use separated antenna and keep them as far as you can on the platform. before going to layout, you may try with TI Kit to learn the performance. I strongly...
View Article