Forum Post: RE: BT - hciattach cmd fails on wl127x
Hi Rohini,The serial port you are using “/dev/ttyO3” is correct?Is the InitScript( .bts file) located at “/lib/firmware/”.Thanks & Regards,Sundeep.
View ArticleForum Post: RE: Impedance matching for RFID
Hi Josh, You're right - most of our competitors adopt differential architecture in their NFC frond end design.However, they still do matching for the HF antenna, whereas they never do matching for LF...
View ArticleForum Post: WI-FI CHIPSET
Hello ,ours basically a product based company working on the Home automation we are planning to use Wi-Fi instead of Zigbee ,can youguys tell us which is the best suitable Wireless Chipset,and also do...
View ArticleForum Post: RE: WL1271 as AP
Hi Abhijit, The driver version is :wl1271: firmware booted (Rev 6.3.3.0.79)wl1271: Driver version: R4_SP2_03_00Now I am able make the interface up as AP, i could see my AP from a station. But still...
View ArticleForum Post: RE: WL1271 as Soft-AP (Hot-Spot) and Station (connected to...
Hi,If you want to use the MR with 1271 you must update the WLAN driver to R5.SP3. best way is to keep the same build of OMAP and follow the PDF that I sent.I hope this helps.Regards,Eran
View ArticleForum Post: RE: Continuous un-modulated transmit mode on the CC1101
You get register settings from SmartRF Studio. Select the "Continuous TX" tab and tick off "unmodulated". In your SW, using the settings from SmartRF Studio, you issue an STX strobe to start TX
View ArticleForum Post: RE: CC1101 / CC1190 best settings for FCC wideband
AN096 gives performance figures for CC1101-CC1190. 250 kbps, +/-127 kHz deviation and 540 kHz RX filter BW gives typically -101 dBm sensitivity. Increasing the deviation to +/-165 kHz and RX filter BW...
View ArticleForum Post: RE: Using address filtering with the CC1101 - not working for me...
Hi RobIt still bugs me that we did not solve this. I have have tested your routine and settings on our HW (CC1101EM and trxEB) and here the address filtering works. If you want I can continue to debug...
View ArticleForum Post: Problems installing CC-Debugger drivers
Hi,I get problems installing the CC-Debugger driver on Windows 7 64bit. It says they are not signed the right way (error 52). I installed the SmartRF Flash, SmartRF Studio and then I also tried the...
View ArticleForum Post: RE: linker error cc2540 application
The said file is not found in the directory.Can this be because the project was build with a previous version of stack?BR Gautam
View ArticleForum Post: RE: cc8530, which 4-channel codec
Hi Kjetil,For four Mic upstream operation with AIC34 and CC8531The following pins from AIC 34 are shorted together.BCLKA & BCLKBWCLKA & WCLKBMCLKA & MCLKBThis is clear, How about the DOUTA,...
View ArticleForum Post: RE: Get CC2540DK MINI (USB-Dongle) to work with (SmartRF) Packet...
Hi Serena,The CC2540 USB dongle must be programmed with different flash images in the two cases. The SmartRF Packet Sniffer flash image is not compatible with the one needed to use the dongle with...
View ArticleForum Post: RE: CC11xx TCXO frequency boundaries
Thanks a lot, this will help for future cases!For now I got solved my problems with 32 MHz TCXO, as I do have enough 40MHz pcs. and TI confirmed that I can use it for 1175.
View ArticleForum Post: RE: SimpliciTI and battery operated radios
Hi Thomas, thank you for your reply. I read the presentation and found there a partial reply to my question: it is written that the current version of FHSS SimpliciTI implementation is not compatible...
View ArticleForum Post: RE: linker error cc2540 application
Hi NickThats exactly what i did...replaced simpleBLEPeripheral files with my files(new) and now there is no error .But now i am using BLEv1.3 only, dint port the project(rather porting dint solve the...
View ArticleForum Post: RE: IEEE Address
Hi My application(project) is BLE.Could you show me the document for IEEE address with BLE(CC2540/CC2541)?Also, how about UUID?And what is function different of UUID & IEEE address?
View ArticleForum Post: RE: BT - hciattach cmd fails on wl127x
Hi Rohini,The serial port associated with UARTX is referred as ttyOX.So depending on the UART configured for Bluetooth the /dev/tty is defined.Could you please provide me your board gpio_en_xxxxx.c...
View ArticleForum Post: Does anybody used Z-stack and LWIP on LM-3S9D96
Hi all, I have installed SW-DK-LM3S9D96-9453.exe,SW-DK-LM3S9D96-EM2-9453.exe and SW-DK-LM3S9B96-EM2-CC2520-ZStack-9107.exe software stacks necessary for DK-LM3S9D96. Now I need to write an application...
View ArticleForum Post: About PurePath Wireless(CC85xx)
I have a few questions on CC8530:1) Without a master programming MCU, what are the default data rate (2M/5M) and audio sampling rate?2) Is uncompressed audio achieved for both 2M and 5M configuration?...
View ArticleForum Post: RE: query regarding replacing AIC3204 with AIC34 in CC85XXDK_HEADSET
Hi Rohit,The VBAT pin on the CC85xx is a pin for battery voltage monitoring, and should be connected directly to the battery voltage via a resistor which is chosen carefully. If you go into the Power...
View Article
