Forum Post: RE: stop a osal_start_timerEx()
Hi Pe,You only need to use osal_stop_timerEx if the osal timer is running (counting down). If the timer has run out and the event has been triggered, (events & NAME_TIMEOUT_EVT) will clear the flag...
View ArticleForum Post: RE: Using address filtering with the CC1101 - not working for me...
Hi RobThat was great news. I'm glad it is all working now.Thanks for the feedback. Example codes can be found on the CC1101 product page, however we have to evaluate how easy it is to find.Good luck...
View ArticleForum Post: RE: Doubt on GFSK, 2-GFSK and 4-GFSK modulations.
Thanks for your immediate reply
View ArticleForum Post: RE: static analysis
HiYou have posted the exact same question and are being followed up in the following post:http://e2e.ti.com/support/low_power_rf/f/155/t/235457.aspxPlease follow up in the original post and do not...
View ArticleForum Post: RE: ADC Ground Reference
[quote user="Eng351"]What is the impedance of the sensor connection to your ADC, is it from a low impedance source like an opamp? The adc has a significant input impedance of a few hundred K which can...
View ArticleForum Post: RE: Orphan indication signal strength in TIMAC
Dear YiKai, Thank you for your reply, I have succeed to debug something without error, but I have not read LQI value, It shows as "0", I want to mention what I have done...Firstly, I have read your...
View ArticleForum Post: RE: static analysis
well when go through datasheets of various devices there will be some timing diagrams listing valid time;setup time etc i.e;that si called static timing nalysis actually it is a method of computing the...
View ArticleForum Post: TI's EMCC430F5137 Board problem - new board
Hi,I am tring to use my EM-CC430F5137 and I keep on getting a message in the CCS the the security fuse is blown.if I am unable to fix this, what is the return policy?I found this in the manual...
View ArticleForum Post: Bluetooth output power questions
We would like to set the maximum transmission power by using HCI_Write_Inquiry_Transmit_Power_Level to 4 dBm. Questions:1. Is this command on the PAN1327/TiCC256x supported?2. If we set the max....
View ArticleForum Post: RE: Sensitivity different od receiving packet via RFStdio from...
If you have problems communicating with a CC1120EM via SPI, please post a plot of the SPI communication.
View ArticleForum Post: RE: Problem about use CC2540 keyfob to communicate with the other...
Hi Weng,Motorola has their own Bluetooth low energy API and the App written for that will most probably not work on your Galaxy tab (not dependent on the hardware in this case but you are right on that...
View ArticleForum Post: RE: Dataexchange with at least 10 slaves
Hi,Currently, our BLEv1.3 stack only supports up to 3 simultaneously connected slaves and if you want to access functionality of more slaves you would need to disconnect and connect to the "other"...
View ArticleForum Post: RE: TRF7970 ISO14443B at higher bit rates
Hi Josh,I also use 2 trf7970a evm.I have expected that i can use higher bit rates for NFC P2P with trf7970a evm modules but i couldnt succed it yet!!Since the fact i have checked the air inteface and...
View ArticleForum Post: RE: Murata wifi/BT module LBEE5ZSTNC-523 and production calibration
do you have any Linux examples that you can share ? Thanks
View ArticleForum Post: RE: 2.4G Meandering F Ant Differences
Hi Eric,Another question about matching. Would it be correct to say the part of the energy circulating in the matching network is not radiating out the antenna? Is this why people say 'you can match...
View ArticleForum Post: OAD For Images Larger Than 128kB
Hello,After reading about the new OAD feature in the 1.3 stack release, it appears that two images must be kept on the 254x at one time, one serving as a pseudo bootloader. Since you must have two...
View ArticleForum Post: RE: TRF7960 won't allow Interrupt Mask register to be modified
Hi Josh,Just to update, I did manage to get more data in together by waiting for the FIFO level high flag - probably something in my code earlier that wasn't correct. However, still see the issue with...
View ArticleForum Post: RE: Intentional Radiation upon loading WL1283 firmware
Hi Mike,The calibrations done in the chip right after the firmware is loaded (without any command from the application) does not involve TX, only Rx.As soon as the application sends a scan/connect...
View ArticleForum Post: Purepath Wireless Audio Headset kit
February 1, 2013 Do any of the University EE classes offer a class project designing wireless headphones or speakers?Do the professors suggest business plan ideas during lectures?The enGadget news...
View Article