Forum Post: RE: cc1180 as node and router in a wireless mesh network
Hi, The Sensinode Nanostack 2.0 LITE that is running on CC1180 is capable of handling about 20-30 nodes per gateway so it depends on how many gateways your are planning to use in your network. Your...
View ArticleForum Post: ZStack networking
Hi all, If I use automatic networking, how do I know networking success or not? Thank you!
View ArticleForum Post: RE: CC2530 can't be recognized by the CC Debugger
Why have you put a 4.7kohm pull-up on the reset pin? This pull-up in combination with the recommended 2.7kohm series resistor is probably preventing the reset pin from being pulled low. Remove the...
View ArticleForum Post: RE: Powering the CC2541 for use with the CC debugger
Hi Sahil, Is the EPG of the CC2541 connected to ground? The recommended decoupling capacitor values are: 100nF for pin 10, 21 and 24 1 uF for pin 39 pin 27, 28 and 29 should share 1x 100nF and 1x...
View ArticleForum Post: CC3000 Datalogger question
In the MSP430 CC3000 data logger example, is it possible to modify the data loggin from intermittent to continuous. How do you extract the data on the PC side? I think the application uses a gui. I...
View ArticleForum Post: Re-establish connection with a BLE peripheral which is not...
Hi All, Is it possible to re-establish connection with a BLE peripheral which is not broadcasting, i.e. only in listening mode? Specifically whenever a link loss happens, can a peripheral get connected...
View ArticleClik here to view.
Forum Post: RE: How to setup CC-6LOWPAN-DK-868
Hello, I have the same problem that cannot get the connection to the router in the nodeview2.0. And in the quick guide step2, I type the command"netsh interface ipv6 address "Local Area Connection"...
View ArticleForum Post: RE: How do I test my CC2540 keyfob based board?
Hi Kazola, I have turned on two "CC2540_Keyfob" board in parallel trying to communicate with "HTC 1V" which supports "BT 4.0" protocol. When scanning for the devices from my mobile phone both of the...
View ArticleForum Post: RE: CC1101 WOR mode problem
Hello TI experts, I have evaluated best sync word used in CC1101 and still I could not figure out exact methodology used by TI in order to determine best sync word (0xD391) My answer is totally...
View ArticleForum Post: RE: CC1101 Selective wake up using WOR
Hello TI experts, I have evaluated best sync word used in CC1101 and still I could not figure out exact methodology used by TI in order to determine best sync word (0xD391) My answer is totally...
View ArticleForum Post: RE: TRF7960 Demo with DK-LM3S9B96
Hi, Are there any updates on this subject ? I am working on ISO15693 implementation for the TRF7960 using the same base code as Michael. I can't get a valid UID reading :...
View ArticleForum Post: RE: Porting CC3000 to PIC32
Hi Shlomi, all right, I think I have now an idea how the driver works. I have made my driver implementation completly new with the latest version. The log with a logic analyser showed me that the IRQ...
View ArticleForum Post: RE: CC3000 Basic Application for STM32
hi , I am currently using TrxRf Based on msp430 and an RF module based on CC1120.mais I like to use the STM32 microprocessor instead of MSP430.donc it is possible to change the MCU in Smart Rf and...
View ArticleForum Post: RE: CC2541 Falsh memory data protection
Thanks for the information, but it leads to futher questions ... So you are saying that I can't use Flash pages 125 or 126 because of potential conflicts with OSAL? How amout the remaining 124 pages?...
View ArticleForum Post: Reading RSSI after a ping on a peer
Hi, is there a simple way to modify the Simpliciti code to get a measurement of an RF signal form a peer, after a SMPL_Ping(peer) was sent. Actually the RSSI is updated only if we received a message...
View ArticleForum Post: RE: CC1120 solution with MCU (MSP430)
hi Martin, I am currently using TrxEB Based on msp430 and an RF module based on CC1120.mais I like to use the STM32 microprocessor instead of MSP430.donc it is possible to change the MCU in Smart Rf...
View ArticleForum Post: RE: Stellaris ARM Cortex sample code to address TRF7960/7970
Hi Eddie I have accepted your invitation. Could you please point me to the right file if it exists already? Thanks Gopi
View ArticleForum Post: RE: WLAN can not working on omap4430 blaze
By default in the console you will be always be user shell, try connecting using adb as root.
View ArticleForum Post: RE: 128bit example
Hi, Yes, of course, I mistyped. If you look at the define in the example it is 112 bits. However, for SIG defined UUIDs you only need 16 bits UUID total. In fact this is how they are defined....
View ArticleForum Post: Zigbee OAD Download for another microcontroller
I have a difficult question... Is it possible to utilize the cc2530 OAD application to download a new program for a TMS320F28062 chip on the same board? My thoughts are to edit the Z-stack OAD...
View Article
