Forum Post: Can 8520 slaves store multiple master IDs?
I have an idea in mind for a system that has multiple components in the system. While it will have multiple masters and slaves in the system, only one master and three slaves will ever be active at...
View ArticleForum Post: RE: CC1101 Address recognition
I haven`t read that section. I`ll do that, thanks. I want to configure all the 5 transceivers with 5 different time periods for the RX mode, so there`s no collision between them. I also noticed that,...
View ArticleForum Post: RE: Sub-1 GHz selection guide
Jinkang, Yes, we have a product overview presentation. From reading you requirements I would recommend looking at the CC1121, it provides very robust wireless links.Our standard development kits for...
View ArticleForum Post: RE: PAN1323 and MSP-EXP430F5438
Thanks for the help. Will carry out the changes told by you.
View ArticleForum Post: RE: Range without amplifier and PCB antenna
Hi Pavel, That sounds a little short - what kind of configuration are you using (number of slaves, number of audio channel, streaming format, latency etc. )If you have access to our CC85XXDK you can do...
View ArticleForum Post: RE: Can 8520 slaves store multiple master IDs?
Kjetil,Thanks for an answer on the weekend. I suspected this was the case but wanted confirmation.Regards,Rodger
View ArticleForum Post: CC2530 and wireless connectivity.
Hello,Together with my collegues, I created custom CC2530 board. Basically it's a circuit from CC2530 Datasheet (page 25) with 2 LED diodes added for very simple "debug" purposes. The chip seems to...
View ArticleForum Post: RE: cc1125 spi
I just did another logic capture and I think I have more specific information to share. I start off by initializing all of my registers. For the first two registers that I transmit to, I get back a...
View ArticleForum Post: RE: UART communication
which pins should i read UART data from?It gives me correct RXBufLen but i cant see any data on P0.2(Rx line),Please helpGautam
View ArticleForum Post: RE: serial port-cc 2531 communication
Hi Maddy,Sorry, I might misunderstand your question. Z-tool is only used for talking to devices with MT command. What FW do you use on your CC2531? ZNP or MT command?
View ArticleForum Post: RE: Using the Zigbee wireless sensor monitor with cc2530zdk
You need to buy a USB to RS232 cable.
View ArticleForum Post: RE: ticon.exe: Script file for winCE
Hi Roykin,In order for the script file to work with the ticon.exe you should modify the parser to be able to handle Windows end of line notation (/r/n) instead of (/n).Regards,Barak
View ArticleForum Post: RE: CC2538 Crystals connection
Connect to Q1. Q2 shall be unconnected. If you use a sine wave, as opposed to a rai-rail digital signal, you need to connect a series capacitor to Q1.
View ArticleForum Post: CC256x and I2S interface
Hi there,I cannot figure out how A2DP profile could be executed on a host processor while an external audio codec is connected to the CC256x through I2S port. In other words, the host processor is...
View ArticleForum Post: RE: WL1271 calibration data with error value
Hi Barak,I follow the step as below from tool and the system with WinCE6.0.I can't reach the FW version and only get the file name(Fw1273r1c_sta_cortex.bin).1. load TrioScopeDll.dll(Ver_0.2.0.5)2. Open...
View ArticleForum Post: RE: SmartRF05EB corruption
Hi Karthiek,Sounds like you have programmed the EBs with CCDebugger firmware. Make sure you are using the bootloader and fw located in the following folder: C:\Program Files\Texas Instruments\SmartRF...
View ArticleForum Post: RE: wl1271 missing APs when scanning
Hi Dennis,I will further investigate and update you.Regards,Barak
View ArticleForum Post: RE: Selection of Wifi module for indoor navigation based on RSSI...
Hi RubenUsing a "Scan" command you can learn about the MAC address of the APs/P2P devices around you. Playing with the scan-configuration, you can get a good update rate.However, in order to understand...
View ArticleForum Post: Meaning of HC_Total_Num_LE_Data_Packets
Page 91 of "TI BLE Vendor Specific HCI Reference Guide Version 1.3" lists the attributes of the "GAP_DeviceInitDone" event, one of them being "numDataPkts". It is given, without any explanation, the...
View ArticleForum Post: RE: cc1125 spi
After I sent the STX command, do I need to wait for GPIO2 to interrupt and let me know that the data has been transmitted over RF before I can send another packet?
View Article