Forum Post: RE: CC2540 Dongle Reference Design + Peripheral Sample Code...
LL_PowerOffReq hangs because the proprietary binary provided by TI checks to make sure you have a 32.768khz external oscillator so that you stay within the BT certification. If you use the RC...
View ArticleForum Post: RE: wl1271 port
Saurabh,Thank you for your prompt response.We see the issue periodically. At times, the module appears to be in some unusuall state and we see the HW_WD_EXPIRE about every 5 minutes.We are using the...
View ArticleClik here to view.
Forum Post: Network processor - can only send out two notifications per event
My configuration: 2x CC2541-EMK in a SOC_BB, connected to a PC. One CC2540 USB dongle acts as the sniffer.The code establishes a session between the master and the slave, then the slave runs this for...
View ArticleForum Post: Want to customize zugbee Sensor Monitor Software
Hi,I have developed my own board with CC2531 where I have attached 1 more sensor (lets say sensor_X ). Now I want to use sensor monitor app to display for sensor_x . I got the source code from one of...
View ArticleForum Post: RE: Range without amplifier and PCB antenna
Hi Kjetil,I use one slave, two channels 44.1kHz PCM16, latency 1024 samples, TX power 5dBm, datarate 5Mbps, protocol A, timeslot period auto (4000us). I haven't access to CC85XXDK. Maybe I will have...
View ArticleForum Post: RE: СС8520 IO pin current
Hi Oleg, on page 8 of datasheet I see these notes under table:1 Digital I/O pad with 4 mA source/sink capability.2 Digital I/O pad with 20 mA source/sink capability.Best regards, Pavel.
View ArticleClik here to view.
Forum Post: RE: cc1125 spi
Ok that is all very helpful.Just to make sure that I'm on the right page...according to "Table 2: Status Byte Summary" on of the manual, the upper 4 bits tell me the status of the chip, and I can...
View ArticleForum Post: AN113 to buy
Hello,I would like to use AN113 for my applicaton. Is this design (all boards, including TX, RX and diversity modules) available for purchasing from TI? What kind of evaluation modules/dev kits it...
View ArticleForum Post: RE: CC112x: Need to change register settings when changing from...
Just to confirm: You want to use transparent mode?SYNC_CFG1: Not relevant in transparent mode since the receiver does know about sync word. Use RX setting.AGC_CFG1: The setting for this register has no...
View ArticleForum Post: RE: CC1125 power consumption
Note that the CC1120 ref design uses the following PCB stack-up (from the readme.txt file in the zip):PCB DESCRIPTION:4 LAYER PCB 1.24 MM nominal Copper 1 35 um Dielectric 1-2 0.4...
View ArticleForum Post: RE: cc2541s
[quote user="Chris Glaser"]The CC2541S will be "compatible" with any external host MCU that can communicate using UART or SPI. We will initially only be releasing host sample code for the MSP430,...
View ArticleForum Post: Wireshark, CC2540 and Bluetooth Smart plugin
Hello Community:Here is a Wireshark plugin for Bluetooth Smart if anyone is interested: Wireshark PlugInLPRF Rocks the World
View ArticleForum Post: RE: Naming Convention for BLE
Yeah, i'd go with Bluetooth Low Energy to be safe
View ArticleForum Post: RE: CC2564 HCI Write Link Supervision Timeout Command Disallowed
This could be because the issuing device is actually a slave. Mike is going to try doing a role switch and reissue the command. Mentioning it here in case someone looks at the thread later....
View ArticleClik here to view.
Forum Post: RE: Playing with the CC85XXDK Wireless Headset demo
Hi Nir,Do the following:Go to the Start Page in the PPW Configurator and double click the example project: CC85XXDK-Wireless Headset (see picture below)The default Master application role is Stereo...
View ArticleForum Post: RE: how to decryption the encrypted packet that capture by packet...
You can download the trial version and you can use it within 30 days.
View ArticleForum Post: The reset time of CC2510
Hello,I want to know the reset time of CC2510.I can't find this from the datasheet of CC2510.Who can tell me about this?Please.Thanks.
View ArticleForum Post: RE: Network processor - can only send out two notifications per...
Well yes, there is enough time in an ideal world, but you must not forget the overhead of processing the messages inside the chip, the processing overhead after each RF event etc. Add to that the fact...
View ArticleForum Post: RE: CC2541DK-SENSOR kit - what software compiler to use with kit?
You need to program the 2540USB dongle with the \Accessories\HexFiles\CC2540_USBdongle_HostTestRelease_All.hex image, the same that is used with BTool.You need a CC debugger to do this. Alternatively...
View Article